manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

5C-12 Clutch: 

8) Set release arm (1) to release shaft (2) aligning 

punch mark (4) of release arm and punch mark (3) of 
release shaft, then tighten bolt to specified torque.

Tightening torque
Release lever bolt (a):  23 N·m (2.3 kg-m, 17.0 lb-
ft)

Clutch Release System Inspection

S4RS0A5306018

Clutch Release Bearing

Check clutch release bearing for smooth rotation. If 
abnormality is found, replace it. 

CAUTION:

Do not wash release bearing. Washing may 
cause grease leakage and consequential 
bearing damage.

 

Clutch Release Shaft

Check clutch release shaft and its pin for deflection or 
damage.
If abnormality is found, replace it.

Specifications

Tightening Torque Specifications

S4RS0A5307001

NOTE:
The specified tightening torque is also described in the following.
“Clutch Fluid Pipe and Hose Components: ”
“Clutch Pedal and Clutch Pedal Bracket Components: ”
“Clutch Cover, Clutch Disc and Flywheel Components: ”

 

Reference:

For the tightening torque of fastener not specified in this section, refer to “Fasteners Information:  in Section 0A”.

I4RS0A530021-

(a) 3

2

4

1

I4RS0A530022-

I3RM0A530020-

I3RM0A530021-

Fastening part

Tightening torque

Note

N

˜

m

kg-m

lb-ft

Clutch operating cylinder bolt

23

2.3

17.0

)

Flywheel bolt

70

7.0

51.0

)

Clutch cover bolt

23

2.3

17.0

)

Release lever belt

23

2.3

17.0

)

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

U.S. General 97845 Set Up And Operating Instructions preview
97845
Бренд: U.S. General Страницы: 5
EAL Formula 523585 Assembly Instructions preview
Formula 523585
Бренд: EAL Страницы: 4
SnapPad EQ Round Installation Instructions preview
EQ Round
Бренд: SnapPad Страницы: 5
Chrysler Stratus LHD 1997 Interactive Electronic Service Manual preview
Stratus LHD 1997
Бренд: Chrysler Страницы: 1534
Phonocar VM350 Mounting Instructions preview
VM350
Бренд: Phonocar Страницы: 2
Wagan Wireless Handsfree Car Kit User Manual preview
Wireless Handsfree Car Kit
Бренд: Wagan Страницы: 20
ULTIMATE SPEED 94600 Assembly And Safety Advice preview
94600
Бренд: ULTIMATE SPEED Страницы: 21
tams elektronik 54-01016 Manual preview
54-01016
Бренд: tams elektronik Страницы: 44
TATA Motors Sumo Victa EX Owner'S Manual & Service Book preview
Sumo Victa EX
Бренд: TATA Motors Страницы: 92
Yakima RimROC Instructions Manual preview
RimROC
Бренд: Yakima Страницы: 12
Axxess AXDSPX-VW1 Installation Instructions Manual preview
AXDSPX-VW1
Бренд: Axxess Страницы: 16
Fab Fours C3150 Installation Instructions Manual preview
C3150
Бренд: Fab Fours Страницы: 21
Rostra RearSight 250-8308 Installation Instructions preview
RearSight 250-8308
Бренд: Rostra Страницы: 2
POOL-LINE 110085 Assembly Instructions preview
110085
Бренд: POOL-LINE Страницы: 2
GYS 029422 Manual preview
029422
Бренд: GYS Страницы: 32
Safe Fleet Prime Design OCM-3032 Quick Start Manual preview
Prime Design OCM-3032
Бренд: Safe Fleet Страницы: 4
Subaru 2015 Forester Quick Reference Manual preview
2015 Forester
Бренд: Subaru Страницы: 16
MMD 41240 Quick Manual preview
41240
Бренд: MMD Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды