manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Air Bag System:  8B-115

4) Remove forward-sensor bolt (1) and forward-sensor 

(2).

Installation

CAUTION:

Proper operation of forward-sensor requires 
sensor be rigidly attached to vehicle 
structure and that the arrow on sensor be 
pointing toward the front of the vehicle.

 

1) Check that none of the following faulty conditions 

exists.
• Bend, deformity or rust of front panel.
• Foreign matter on mating surface of sensor.

2) Apply thread lock cement to mounting bolts thread. 

Install forward-sensor (1) on front panel and tighten 
mounting bolt (2) to specified torque.

“A”:  Thread lock cement 99000–32100

Tightening torque
Forward-sensor mounting bolt (a):  9 N·m (0.9 
kg-m, 6.5 lb-ft)

3) Connect forward-sensor connector by pushing 

connector till click is heard from it.

4) Connect negative cable at battery.
5) Enable air bag system referring to “Enabling Air Bag 

System: ”.

Forward-Sensor Inspection

S4RS0A8206010

WARNING:

During service procedures, be very careful 
when handling a sensor.
• Never strike or jar a sensor.
• A sensor and mounting bracket bolts must 

be carefully torqued to assure proper 
operation. Under loose connection, it 
could cause improper operation of the air 
bag system.

 

CAUTION:

• Never disassemble forward-sensor.
• Sensor should be replaced when it was 

dropped from a height of 90 cm (3 ft) or 
more.

 

• Check sensor for dents, cracks or deformation.
• Check sensor connector (sensor side and harness 

side) and sensor connector lock mechanism for 
damage or crack.

• Check connector terminals for bend, corrosion or rust.

Side-Sensor Removal and Installation

S4RS0A8206023

WARNING:

During service procedures, be very careful 
when handling a sensor.
• Never strike or jar a sensor.
• A sensor bolt must be carefully torqued to 

assure proper operation. Under loose 
connection, it could cause improper 
operation of the air bag system.

 

Removal

1) Disconnect negative (–) cable at battery.
2) Disable air bag system. Refer to “Disabling Air Bag 

System: ”.

3) Remove center pillar lower trim and side sill scuff.
4) Turn up floor carpet at front seat side.
5) Remove side-sensor bolt (1), and side-sensor (2) 

from under body (3).

1

2

I5RH01820119-

2,"A",(a)

1

I5RH01820120-

1

2

3

I4RS0A820080-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

AC Schnitzer F40 Fitting Instructions Manual preview
F40
Бренд: AC Schnitzer Страницы: 16
Kargo Master 40020 Assembly Manual preview
40020
Бренд: Kargo Master Страницы: 6
Hama Neptun Manual preview
Neptun
Бренд: Hama Страницы: 6
Porsche 911 GT3R 2010 Technical Manual preview
911 GT3R 2010
Бренд: Porsche Страницы: 144
Whispbar K611W Fitting Instructions Manual preview
K611W
Бренд: Whispbar Страницы: 77
Monacor Carpower CAP-20 Quick Manual preview
Carpower CAP-20
Бренд: Monacor Страницы: 2
Subaru 1998 Forester Owner'S Manual preview
1998 Forester
Бренд: Subaru Страницы: 298
THIEYE CarView 2 User Manual preview
CarView 2
Бренд: THIEYE Страницы: 88
Thule RaceWay 991 Instructions Manual preview
RaceWay 991
Бренд: Thule Страницы: 12
TOGU Airgo Active cushion / Comfort Manual And Maintenance Instructions preview
Airgo Active cushion / Comfort
Бренд: TOGU Страницы: 2
Motoalliance Denali MA11737 Manual preview
Denali MA11737
Бренд: Motoalliance Страницы: 4
Volvo Ski box Installation Instructions Manual preview
Ski box
Бренд: Volvo Страницы: 7
Kia 2015 optima Quick Start Manual preview
2015 optima
Бренд: Kia Страницы: 5
Prorack K890 Fitting Instructions Manual preview
K890
Бренд: Prorack Страницы: 15
PAC BCI-FD21 Instructions preview
BCI-FD21
Бренд: PAC Страницы: 4
Ferrari GTC 4 Lusso Roadside Assistance Manual preview
GTC 4 Lusso
Бренд: Ferrari Страницы: 45
Honda 2012 CIVIC SEDAN EX Technology Reference Manual preview
2012 CIVIC SEDAN EX
Бренд: Honda Страницы: 10
Kia Ceed 2016 Quick Reference Manual preview
Ceed 2016
Бренд: Kia Страницы: 10

Бренды по названию

Популярные бренды

Загрузить еще бренды