manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

7A-10 Heater and Ventilation: 

Center Ventilation Louver Removal and 
Installation

S4RS0A7106014

Removal

1) Disconnect negative (–) cable from battery.
2) Disable air bag system referring to “Disabling Air 

Bag System:  in Section 8B”.

3) Remove passenger air bag module from instrument 

panel referring to “Passenger Air Bag (Inflator) 
Module Removal and Installation:  in Section 8B”.

4) Remove radio assembly from instrument panel 

referring to “Radio Assembly Removal and 
Installation:  in Section 9C”.

5) Remove center ventilation louver (1) with garnish (2) 

from instrument panel, and then disconnect 
connector from hazard switch.

NOTE:
Garnish is fitted to instrument panel with six 
clips. When removing garnish from 
instrument panel, be careful not to break 
them.

 

6) Separate center ventilation louver and garnish.

Installation

Reverse removal procedure.

Side Ventilation Louver Removal and 
Installation

S4RS0A7106015

Right side ventilation louver

Removal

1) Disconnect negative (–) cable from battery.
2) Disable air bag system referring to “Disabling Air 

Bag System:  in Section 8B”.

3) Remove steering column hole cover from instrument 

panel.

4) Remove combination meter cluster panel from 

instrument panel, and then disconnect connector 
from front fog lamp switch of combination meter 
cluster panel.

5) Separate right side ventilation louver (1) and 

combination meter cluster (2).

Installation

Reverse removal procedure noting the following 
instruction.
• Right side ventilation louver is fitted to combination 

meter cluster panel with four clips (1). When installing 
right side ventilation louver to combination meter 
cluster panel, position the smallest clip to the top.

Left side ventilation louver

Removal

1) Disconnect negative (–) cable from battery.
2) Disable air bag system referring to “Disabling Air 

Bag System:  in Section 8B”.

3) Remove glove box from instrument panel.

1

2

I4RS0A710024-

2

1

I4RS0A710025-

1

I4RS0A710026-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Daihatsu TERIOS J100 Maintenance Manual preview
TERIOS J100
Бренд: Daihatsu Страницы: 43
Kargo Master 80070 Assembly Lnstructions preview
80070
Бренд: Kargo Master Страницы: 13
Kargo Master 4A96L Installation Manual preview
4A96L
Бренд: Kargo Master Страницы: 21
Kargo Master 40201 Installation Manual preview
40201
Бренд: Kargo Master Страницы: 4
Whispbar K934W Fitting Instructions Manual preview
K934W
Бренд: Whispbar Страницы: 15
Gatorback Mudflaps GCR53F Mounting Diagram & Instructions preview
GCR53F
Бренд: Gatorback Mudflaps Страницы: 4
Opel 2011 Insignia Owner'S Manual preview
2011 Insignia
Бренд: Opel Страницы: 254
Scosche BTFREQ PRO BTFMPD3SR Manual preview
BTFREQ PRO BTFMPD3SR
Бренд: Scosche Страницы: 16
Icom RMK-5 Instruction Manual preview
RMK-5
Бренд: Icom Страницы: 20
T-Mobile SyncUP DRIVE Start Manual preview
SyncUP DRIVE
Бренд: T-Mobile Страницы: 2
FALCON RIDGE HU-4421-XL-SDK01 Instructions For Installation And Care preview
HU-4421-XL-SDK01
Бренд: FALCON RIDGE Страницы: 5
Webasto Telestart T70 Installation Instructions Manual preview
Telestart T70
Бренд: Webasto Страницы: 23
Honda 2007 Fit User Information preview
2007 Fit
Бренд: Honda Страницы: 24
Volvo M3602654 Installation Instructions Manual preview
M3602654
Бренд: Volvo Страницы: 10
Connects2 CTUPO01 Quick Start Manual preview
CTUPO01
Бренд: Connects2 Страницы: 8
RAM Cargo Van 2014 Owner'S Manual preview
Cargo Van 2014
Бренд: RAM Страницы: 666
Waeco PerfectView LCD350 Installation And Operating Manual preview
PerfectView LCD350
Бренд: Waeco Страницы: 36
Curt Group Aries AL235045 Installation Manual preview
Aries AL235045
Бренд: Curt Group Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды