manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

9J-4 Hood / Fenders / Doors: 

• When replacing door, coat replacement door inside 

with wax for proper anti-corrosion treatment. Refer to 
“Sealant Application Areas:  in Section 9L”.

• Apply sealant to contact face “A” of hinge (1) and 

apply grease to rotating part “B” of hinge (1).
Specified sealant and grease.

“A”:  Sealant 99000–31110
“B”:  Grease 99000–25010

• Tighten hinge bolt to specified torque.

Tightening torque
Door hinge mounting bolt (body side) (a):  27 N·m 
(2.7 kg-m, 19.5 lb-ft)
Door hinge mounting bolt (door side) (b):  23 N·m 
(2.3 kg-m, 17.0 lb-ft)

• When door open stopper (1) is installed, be careful 

make sure punch mark (2) comes to the top.

Door open stopper installing direction
Left side door: L punch mark is upward
Right side door: R punch mark is upward

• Tighten door open stopper bolt (3) to specified torque.

Tightening torque
Door open stopper bolt (a):  21 N·m (2.1 kg-m, 
15.5 lb-ft)

• Adjust door latch striker position referring to “Front 

Door Lock Assembly Removal and Installation:  in 
Section 9F”.

• Adjust front door cushion so that door becomes flush 

with side body.

• After installation, open and close the door to check 

looseness. 

Rear Door Assembly Components

S4RS0A9A06007

I4RS0A9A0007-

I4RS0A9A0008-

2

2

(a)

4

(a)

4

(a)

7

(a)

7

(b)

5

3

6

1

I4RS0A9A0009-

1. Door panel

4. Rear door hinge bolt

7. Rear door hinge nut

 

 2. Door hinge 

: Apply lithium grease 99000-25010 to rotating part.
: Apply sealant 99000-31110 to contact face.

5. Door open stopper bolt

: 23 N

˜

m (2.3 kg-m, 17.0 lb-ft)

3. Door open stopper

6. Rear door opening weather-strip

: 21 N

˜

m (2.1 kg-m, 15.5 lb-ft)

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

ZAPTEC Go Instruction Manual preview
Go
Бренд: ZAPTEC Страницы: 240
RaceChip Pro 2 Installation Manual preview
Pro 2
Бренд: RaceChip Страницы: 12
Harmar Mobility AL001 Installation And Owner'S Manual preview
AL001
Бренд: Harmar Mobility Страницы: 10
RAM Commercial PROMASTER 2020 Quick Reference Manual preview
PROMASTER 2020
Бренд: RAM Commercial Страницы: 12
Fiat 500 L 2019 User Manual preview
500 L 2019
Бренд: Fiat Страницы: 172
Honda HondaLink Quick Start Manual preview
HondaLink
Бренд: Honda Страницы: 6
Rati Armster 2 User Manual preview
Armster 2
Бренд: Rati Страницы: 2
TBC 645624 Instruction Manual preview
645624
Бренд: TBC Страницы: 12
Prorack K194 Fitting Instructions For Basic Carrier preview
K194
Бренд: Prorack Страницы: 14
Fiat Fiat Bravo LPG Owner'S Manual preview
Fiat Bravo LPG
Бренд: Fiat Страницы: 24
Valeo AS1A Owner'S Manual preview
AS1A
Бренд: Valeo Страницы: 28
Brodit ProClip 854208 Manual preview
ProClip 854208
Бренд: Brodit Страницы: 2
Broadfeet RSLX-385-68S Installation Instructions preview
RSLX-385-68S
Бренд: Broadfeet Страницы: 2
Buick Riviera 1967 Owner'S Manual preview
Riviera 1967
Бренд: Buick Страницы: 58
Coulomb Technologies ChargePoint CT500-DSTAND Installation Manual preview
ChargePoint CT500-DSTAND
Бренд: Coulomb Technologies Страницы: 26
Kleinn Air Horns RNGR-102-1/220 Installation Manual preview
RNGR-102-1/220
Бренд: Kleinn Air Horns Страницы: 33
AL-KO 605 363 Operating Instructions Manual preview
605 363
Бренд: AL-KO Страницы: 88
Ford Mondeo 2007 Owner'S Handbook Manual preview
Mondeo 2007
Бренд: Ford Страницы: 292

Бренды по названию

Популярные бренды

Загрузить еще бренды