manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

10B-18 Body Electrical Control System: 

DTC B1141 / DTC B1142 / DTC B1143 (No.1141 / No. 1142/ No. 1143) Outside Air Temperature 
(Ambient Temp.) Sensor Circuit Malfunction

S4RS0AA204022

Wiring Diagram

DTC Detecting Condition and Possible Cause

Flow Test Description
Step 1: 

Check whether malfunction is in outside air temperature sensor.

Step 2: 

Check outside air temperature sensor input circuit.

Step 3: 

Check outside air temperature sensor ground circuit (for DTC B1141 and B1143).

I4RS0AA20010-

[A]: BCM connector viewed from harness side

3. Junction block assembly

1. Outside air temperature sensor

4. Outside air temperature sensor connector

2. BCM

DTC detecting condition

Possible cause

DTC B1141 (DTC No. 1141):

Input signal from outside air temperature sensor is higher 
than 4.88 V.

• Open in outside air temperature sensor circuit
• Outside air temperature sensor malfunction
• BCM malfunction

DTC B1142 (DTC No. 1142):

Input signal from outside air temperature sensor is lower 
than 0.1 V.

• Short in outside air temperature sensor circuit
• Outside air temperature sensor malfunction
• BCM malfunction

DTC B1143 (DTC No. 1143):

Input signal from outside air temperature sensor is 0.1 - 
0.27 V or 4.6 - 4.88 V.

• High resistance in outside air temperature sensor 

circuit

• Outside air temperature sensor malfunction
• BCM malfunction

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Warrior Products 3860 Quick Start Manual preview
3860
Бренд: Warrior Products Страницы: 2
Q'STRAINT QLK-150 Installation Instructions Manual preview
QLK-150
Бренд: Q'STRAINT Страницы: 10
Yakima SkyBox 12 Installation Instructions Manual preview
SkyBox 12
Бренд: Yakima Страницы: 6
Yakima HoldUp Plus2 Manual preview
HoldUp Plus2
Бренд: Yakima Страницы: 18
Allen Sports QR545 Instructions preview
QR545
Бренд: Allen Sports Страницы: 2
PullRite 20K OE Series Installation Instructions Manual preview
20K OE Series
Бренд: PullRite Страницы: 10
ECS Electronics CR-066-BHU Manual preview
CR-066-BHU
Бренд: ECS Electronics Страницы: 16
Actia TGU-R ACCESS User Manual preview
TGU-R ACCESS
Бренд: Actia Страницы: 37
Gatorback Mudflaps GCR53F Mounting Diagram & Instructions preview
GCR53F
Бренд: Gatorback Mudflaps Страницы: 4
Fab Fours F2950 Installation Instructions Manual preview
F2950
Бренд: Fab Fours Страницы: 21
iOttie Aivo Connect Setup Manual preview
Aivo Connect
Бренд: iOttie Страницы: 58
mtf TRANSPORT SYSTEM BackPower Manual preview
BackPower
Бренд: mtf TRANSPORT SYSTEM Страницы: 9
Cadillac 54-6219 1954 Shop Manual preview
54-6219 1954
Бренд: Cadillac Страницы: 409
Fortin THAR-AUD1 Manual preview
THAR-AUD1
Бренд: Fortin Страницы: 9
Gator GHWCUSB2 User Manual preview
GHWCUSB2
Бренд: Gator Страницы: 8
benbat BM721 Instructions For Use Manual preview
BM721
Бренд: benbat Страницы: 14
SPL FE Z33 Installation Instructions preview
FE Z33
Бренд: SPL Страницы: 5
Omix-Ada 11704.05 Owner'S Manual preview
11704.05
Бренд: Omix-Ada Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды