manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

9B-9 Lighting Systems: 

Stop (Brake) Lamp Switch Inspection

S4RS0A9206011

Check stop (brake) lamp switch for continuity between 
terminals at each switch position.
If check result is not as specified, replace switch.

Turn Signal Light Switch (in Lighting Switch) 
Removal and Installation

S4RS0A9206012

For removal and Installation, refer to “Headlight Switch 
(in Lighting Switch) Removal and Installation: ”.

Turn Signal Light Switch (in Lighting Switch) 
Inspection

S4RS0A9206013

Check for continuity between terminals at each switch 
position. If check result is not as specified, replace 
switch.

Turn Signal and Hazard Warning Relay Removal 
and Installation

S4RS0A9206020

Removal

1) Disconnect negative (–) cable at battery.
2) Remove junction block assembly referring to “BCM 

(Included in Junction Block Assembly) Removal and 
Installation:  in Section 10B”.

3) Remove turn signal and hazard warning relay.

Installation

Reverse removal procedure for installation.

Turn Signal and Hazard Warning Relay 
Inspection

S4RS0A9206021

1) Connect turn signal and hazard warning relay (1), 

battery (2) and six test bulbs ((12V, 21W) (3) and 12 
V, 5W (4)) as shown.

2) Check turn L circuit

Connect terminal “5” and battery negative (–) 
terminal by a jumper wire.
Check left side bulbs (1) for flashing cycle.
If check result is not as specified, replace turn signal 
and hazard warning relay.

Reference flashing cycle
60 – 120 cycle/minute

4

2

3

1

Terminal

Shaft condition

FREE

PUSH

1

2

3

4

I4RS0A920012-

L

R

Terminal

Turn signal SW

3

1

2

L

N
R

1

2

3

I4RS0A920013-

2

4

3

3

3

8

7

1

2

6

5 4

1

I4RS0A920014-

1

3

8

7

1

2

6

5 4

I4RS0A920015-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Jeep Cherokee 16 1982 Technical & Service Manual preview
Cherokee 16 1982
Бренд: Jeep Страницы: 1311
Roav R5141 Owner'S Manual preview
R5141
Бренд: Roav Страницы: 10
Neuspeed 25.02.22.2 Installation Instructions preview
25.02.22.2
Бренд: Neuspeed Страницы: 2
Prorack K383 Fitting Instructions Manual preview
K383
Бренд: Prorack Страницы: 14
Sirius Satellite Radio Streamer GTR Installation Manual preview
Streamer GTR
Бренд: Sirius Satellite Radio Страницы: 8
Waeco MagicWatch MWE250 Installation And Operating Manual preview
MagicWatch MWE250
Бренд: Waeco Страницы: 172
VDO DLD Wide Range II Installation Instructions Manual preview
DLD Wide Range II
Бренд: VDO Страницы: 84
Wagan TravelCharge Companion GO-Plus User Manual preview
TravelCharge Companion GO-Plus
Бренд: Wagan Страницы: 3
Jeep PATRIOT 2013 Manual preview
PATRIOT 2013
Бренд: Jeep Страницы: 16
Audi RSE III Quick Start Manual preview
RSE III
Бренд: Audi Страницы: 4
Fab Fours F2950 Installation Instructions Manual preview
F2950
Бренд: Fab Fours Страницы: 21
Gator GHWCUSB2 User Manual preview
GHWCUSB2
Бренд: Gator Страницы: 8
benbat BM721 Instructions For Use Manual preview
BM721
Бренд: benbat Страницы: 14
SPL FE Z33 Installation Instructions preview
FE Z33
Бренд: SPL Страницы: 5
Mynew Portable Car Umbrella User Manual preview
Portable Car Umbrella
Бренд: Mynew Страницы: 5
Brodit ProClip 854676 Quick Start Manual preview
ProClip 854676
Бренд: Brodit Страницы: 2
Acura TSX 2014 Advanced Technology Manual preview
TSX 2014
Бренд: Acura Страницы: 19
Ford 2009 Edge Owner'S Manual preview
2009 Edge
Бренд: Ford Страницы: 325

Бренды по названию

Популярные бренды

Загрузить еще бренды