manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

10C-10 Immobilizer Control System: 

DTC P1622 EEPROM Error

S4RS0AA304030

Possible Cause and Trouble Area

Troubleshooting

1) Clear DTC(s) referring to “Diagnostic Trouble Code (DTC) Clearance: ”.
2) Turn the ignition switch to OFF position.
3) Check if DTC P1622 is still detected referring to “Diagnostic Trouble Code (DTC) Check: ”. If still detected, go to 

the next step. If not, the troubleshooting is completed.

4) Replace ECM with new one referring to “Engine Control Module (ECM) Removal and Installation:  in Section 1C”.
5) Perform “Procedure after ECM Replacement: ”.

DTC P1623 Unregistered Transponder

S4RS0AA304031

Possible Cause and Trouble Area

Troubleshooting

13

Check for short of “YEL/BLK” and “YEL/RED” wires:

1) With immobilizer control module connector “G24” and 

ECM connector “E23” disconnected, check resistance 
between “G24-3” wire terminal and “G24-4” wire terminal 
at immobilizer control module connector.

Is resistance infinite?

Go to Step 14.

Repair short of “YEL/
BLK” and “YEL/RED” 
wires.

14

Check for fault of immobilizer control module:

1) Check immobilizer control module referring to 

“Inspection of Immobilizer Control Module and Its Circuit: 
”.

Is immobilizer control module normal?

Replace ECM with new 
one referring to “Engine 
Control Module (ECM) 
Removal and 
Installation:  in Section 
1C”, and then perform 
“Procedure after ECM 
Replacement: ”.

Replace immobilizer 
control module with new 
one referring to 
“Immobilizer Control 
Module Removal and 
Installation: ”.

Step

Action

Yes

No

Possible Cause

Trouble Area

• Temporary error
• Internal failure (EEPROM corruption) of ECM

ECM

Possible Cause

Trouble Area

• Temporary error
• Use of the unregistered ignition key
• Immobilizer control module faulty
• ECM faulty

• Transponder in the ignition key
• Immobilizer control module
• ECM

Step

Action

Yes

No

1

Diagnostic Trouble Code (DTC) confirmation:

1) Clear DTC(s) referring to “Diagnostic Trouble Code 

(DTC) Clearance: ”.

2) Turn the ignition switch to OFF position.
3) Check if any DTC is detected referring to “Diagnostic 

Trouble Code (DTC) Check: ”.

Is DTC P1623 still detected?

Go to Step 2.

The troubleshooting is 
completed.

2

Diagnostic Trouble Code (DTC) check:

1) Check if any DTC other than P1623 is detected referring 

to “Diagnostic Trouble Code (DTC) Check: ”.

Is any DTC other than P1623 is detected?

Perform troubleshooting 
referring to the 
corresponding flowchart 
in this section, and then 
go to Step 3.

Go to Step 3.

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Jeep Automobile Service And Warranty Handbook preview
Automobile
Бренд: Jeep Страницы: 42
Jeep Automobile Warranty Information Booklet preview
Automobile
Бренд: Jeep Страницы: 44
Cadillac ATS 2015 Convenience/Personalization Manual preview
ATS 2015
Бренд: Cadillac Страницы: 20
Jeep Automobile Service Contract preview
Automobile
Бренд: Jeep Страницы: 7
Cadillac 2016 ELR Convenience/Personalization Manual preview
2016 ELR
Бренд: Cadillac Страницы: 20
Cadillac 2016 CTS Manual preview
2016 CTS
Бренд: Cadillac Страницы: 354
Cadillac 2005 CTS Personalization Manual preview
2005 CTS
Бренд: Cadillac Страницы: 20
Cadillac 2014 XTS Convenience/Personalization Manual preview
2014 XTS
Бренд: Cadillac Страницы: 20
Cadillac ATS 2014 Specifications preview
ATS 2014
Бренд: Cadillac Страницы: 10
Cadillac 2013 Escalade ESV Owner'S Manual preview
2013 Escalade ESV
Бренд: Cadillac Страницы: 524
Cadillac 2013 ATS Personalization Manual preview
2013 ATS
Бренд: Cadillac Страницы: 20
Cadillac ATS 2013 Owenrs Manual preview
ATS 2013
Бренд: Cadillac Страницы: 438
Cadillac 2013 ATS Owner'S Manual preview
2013 ATS
Бренд: Cadillac Страницы: 450
Cadillac 2011 Escalade Hybrid Owner'S Manual Addendum preview
2011 Escalade Hybrid
Бренд: Cadillac Страницы: 94
Cadillac 2011 Escalade Hybrid Owner'S Manual preview
2011 Escalade Hybrid
Бренд: Cadillac Страницы: 94
Cadillac 2011 CTS COUPE Navigation Manual preview
2011 CTS COUPE
Бренд: Cadillac Страницы: 78
Cadillac 2011 CTS COUPE Brochure preview
2011 CTS COUPE
Бренд: Cadillac Страницы: 8
Cadillac 2010 Escalade Manual preview
2010 Escalade
Бренд: Cadillac Страницы: 113

Бренды по названию

Популярные бренды

Загрузить еще бренды