manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

8B-126 Air Bag System: 

5) Check that there is no open, short or damage in 

special tools (deployment harness (A), adapter cable 
(B) and (C)). If any faulty condition is found, do not 
use it and be sure to use new special tool. And 
connect adapter cable (B), (C) or (D) to deployment 
harness (A) and lock connectors with lock slider.

Special tool
(A):  09932-75031
(B):  09932–77310
(C):  09932–78332
(D):  09932–76510

6) Short two deployment harness leads together by 

fully seating one banana plug into the other.

WARNING:

Deployment harness (A) shall remain shorted 
and not be connected to 12 volts vehicle 
battery until you are ready to deploy air bag 
(inflator) module or activate seat belt 
pretensioner.

 

7) Connect adapter cable (B) or (C) in series with 

deployment harness (A) to air bag (inflator) module 
or seat belt pretensioner as follows.
• For driver and passenger air bag (inflator) module 

[A]
Connect adapter cable (B) in series with 
deployment harness (A) and push adapter cable 
(B) connector to air bag (inflator) module 
connector till click can be heard.

• For side-air bag (inflator) module [B]

Connect adapter cable (C) in series with 
deployment harness (A) and push adapter cable 
(C) connector to side bag (inflator) module 
connector till click can be heard.

• For side curtain-air bag (inflator) module [C]

Connect adapter cable (D) in series with 
deployment harness (A) to curtain bag (inflator) 
module and lock connector with lock part.

• For seat belt pretensioners [D]

Connect adapter cable (D) in series with 
deployment harness (A) to seat belt pretensioner 
and lock connector with lock part.

8) Route deployment harness (1) out of vehicle.
9) Check that inside of vehicle and area surrounding 

vehicle are clear of all people and loose or 
flammable objects.

10) Stretch deployment harness (1) to its full length 10 m 

(33 ft).

11) Place 12 volts vehicle battery (2) near shorted end of 

deployment harness (1).

[A]

[C]

[D]

1

2

1

2

1

(B)

(A)

[B]

1

(C)

(A)

1

(D)

(A)

(A)

(D)

1

I4RS0A820094-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Acdeos AXS FL Manual preview
AXS FL
Бренд: Acdeos Страницы: 38
RAM 2015 1500 User Manual preview
2015 1500
Бренд: RAM Страницы: 292
RAM Trucks 1500 User Manual preview
Trucks 1500
Бренд: RAM Страницы: 116
TATA Motors nano genX Owner'S Manual preview
nano genX
Бренд: TATA Motors Страницы: 156
TUFLOC Dodge Charger TufBox Installation Instructions Manual preview
Dodge Charger TufBox
Бренд: TUFLOC Страницы: 6
Mazda 2006 RX-8 Service Highlights preview
2006 RX-8
Бренд: Mazda Страницы: 122
Toyota CAMRY HV Manual preview
CAMRY HV
Бренд: Toyota Страницы: 636
Oldsmobile 2000 Oldsmobile Intrigue Owner'S Manual preview
2000 Oldsmobile Intrigue
Бренд: Oldsmobile Страницы: 348
Subaru 1994 Impreza Supplemental Service Manual preview
1994 Impreza
Бренд: Subaru Страницы: 540
Mont Blanc ACTIVA+ Assembly Instructions preview
ACTIVA+
Бренд: Mont Blanc Страницы: 2
HAKR TRIP 3 Instructions For Use Manual preview
TRIP 3
Бренд: HAKR Страницы: 9
Toyota 2012 Sienna Owner'S Manual preview
2012 Sienna
Бренд: Toyota Страницы: 779
Volvo XC60 2014 Wiring Diagrams preview
XC60 2014
Бренд: Volvo Страницы: 362
Edelbrock PRO-FLO XT 3527 User Manual preview
PRO-FLO XT 3527
Бренд: Edelbrock Страницы: 39
Nav TV NTV-KIT850 Install Manual preview
NTV-KIT850
Бренд: Nav TV Страницы: 11
Kia 2015 Soul Features & Functions Manual preview
2015 Soul
Бренд: Kia Страницы: 46
Volvo XC60 2009 Owner'S Manual preview
XC60 2009
Бренд: Volvo Страницы: 304
Prime Design VRI3-FT31B Assembly Manual preview
VRI3-FT31B
Бренд: Prime Design Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды