manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Security and Locks:  9F-9

Rear Door Lock Assembly Components

S4RS0A9606007

Rear Door Lock Assembly Removal and 
Installation

S4RS0A9606008

Removal

1) Remove rear door glass referring to “Rear Door 

Glass Removal and Installation:  in Section 9E”.

2) Disconnect door lock motor lead wire.
3) Remove door latch mounting screws (1) and remove 

door latch assembly (2).

Installation

Reverse removal procedure to install rear door lock 
assembly referring to the following instruction and “Front 
Door Lock Assembly Removal and Installation: ”.
• Tighten door latch screw to specified torque.

Tightening torque
Door latch screw (a):  5.0 N·m (0.5 kg-m, 4.0 lb-ft)

Rear Door Lock Assembly Inspection

S4RS0A9606009

• Check that door opens and closes smoothly and 

properly.

• Check that door stops in the secondary latched 

position properly (preventing door from opening 
freely) and that door closes completely in the fully 
latched position.

• Adjust door latch striker position, if necessary.

(a)

(b)

1

7

2

6

3

4

5

I4RS0A960012-

1. Outside handle

: Apply lithium grease 99000-25010 to sliding part.

4. Latch striker

7. Out side handle cap

2. Outside handle frame

: Apply lithium grease 99000-25010 to sliding part and spring.

5. Shim

: 5.0 N

˜

m (0.5 kg-m, 4.0 lb-ft)

3. Rear door latch assembly 

: Apply lithium grease 99000-25010 to sliding part.

6. Inside handle bezel

: 10 N

˜

m (1.0 kg-m, 7.5 lb-ft)

1

2

I4RS0A960013-

(a)

I4RS0A960014-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

AAMP of America iSimple Operation Manual preview
iSimple
Бренд: AAMP of America Страницы: 6
Jabra TOUR Get Started preview
TOUR
Бренд: Jabra Страницы: 10
Jeep PATRIOT 2013 Specifications preview
PATRIOT 2013
Бренд: Jeep Страницы: 5
Jeep PATRIOT 2012 Specifications preview
PATRIOT 2012
Бренд: Jeep Страницы: 6
Jeep Grand Cherokee SRT 2014 Operating Manual preview
Grand Cherokee SRT 2014
Бренд: Jeep Страницы: 345
Jeep Grand Cherokee 2015 User Manual preview
Grand Cherokee 2015
Бренд: Jeep Страницы: 236
Jeep Grand Cherokee Quick Manual To Repairs preview
Grand Cherokee
Бренд: Jeep Страницы: 18
Jeep Grand Cherokee Quick Reference Manual preview
Grand Cherokee
Бренд: Jeep Страницы: 24
Jeep Compass 2015 Owner'S Manual preview
Compass 2015
Бренд: Jeep Страницы: 560
Jeep Compass 2013 Owner'S Manual preview
Compass 2013
Бренд: Jeep Страницы: 525
Jeep Cherokee 2019 User Manual preview
Cherokee 2019
Бренд: Jeep Страницы: 308
Jeep CHEROKEE 2017 Manual preview
CHEROKEE 2017
Бренд: Jeep Страницы: 86
Jeep CHEROKEE 2017 Owner'S Manual preview
CHEROKEE 2017
Бренд: Jeep Страницы: 638
Jeep 2022 CHEROKEE Quick Start Manual preview
2022 CHEROKEE
Бренд: Jeep Страницы: 9
Jeep 2014 Patriot Service Information preview
2014 Patriot
Бренд: Jeep Страницы: 51
Jeep Jeep Wrangler Buyer'S Manual preview
Jeep Wrangler
Бренд: Jeep Страницы: 4
Jeep Jeep Wrangler Owner'S Manual Supplement preview
Jeep Wrangler
Бренд: Jeep Страницы: 50
Jeep Grand Cherokee SRT 2014 Owner'S Manual preview
Grand Cherokee SRT 2014
Бренд: Jeep Страницы: 118

Бренды по названию

Популярные бренды

Загрузить еще бренды