manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

2D-6 Wheels and Tires: 

Wheel Removal and Installation

S4RS0A2406003

Removal

1) Loosen wheel nuts by approximately 180 

q

 (half a 

rotation).

2) Hoist vehicle.
3) Remove wheel.

CAUTION:

Never use heat to loosen tight wheel because 
application of heat to wheel can shorten life 
of wheel and damage wheel bearings.

 

Installation

For installation, reverse removal procedure, noting the 
following.
• Wheel nuts must be tightened in sequence and to 

proper torque to avoid bending wheel or brake disc.

NOTE:
Before installing wheels, remove any build-
up of corrosion on wheel mounting surface 
and brake disc mounting surface by scraping 
and wire brushing. Installing wheels without 
good metal-to-metal contact at mounting 
surfaces can cause wheel nuts to loosen, 
which can later allow a wheel to come off 
while vehicle is moving.

 

Tightening order
“A” – “B” – “C” – “D”

Tightening torque
Wheel nut (a):  85 N·m (8.5 kg-m, 61.5 lb-ft)

Tire Mounting and Dismounting

S4RS0A2406004

Use a tire changing machine to mount or dismount tires. 
Follow equipment manufacturer’s instructions. Do not 
use hand tools or tire irons alone to change tires as they 
may damage tire beads or wheel rim.
Rim bead seats should be cleaned with a wire brush or 
coarse steel wool to remove lubricants, old rubber and 
light rust. Before mounting or dismounting a tire, bead 
area should be well lubricated with approved tire 
lubricant.
After mounting, inflate to specified pressure shown on 
tire placard so that beads are completely seated.

WARNING:

Do not stand over tire when inflating. Bead 
may break when bead snaps over rim’s safety 
hump and cause serious personal injury.
Do not exceed specified pressure when 
inflating. If specified pressure will not seat 
beads, deflate, re-lubricate and reinflate.
Over inflation may cause bead to break and 
cause serious personal injury.

 

Install valve core and inflate to proper pressure.

Tire Repair

S4RS0A2406005

There are many different materials and techniques on 
the market to repair tires. As not all of these work on all 
types of tires, tire manufacturers have published detailed 
instructions on how and when to repair tires. These 
instructions can be obtained from each tire 
manufacturer.

I2RH01240010-

I2RH01240011-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

U.S. General 97845 Set Up And Operating Instructions preview
97845
Бренд: U.S. General Страницы: 5
Saab B205 Installation Instructions Manual preview
B205
Бренд: Saab Страницы: 10
Vauxhall Meriva Quick Reference Manual preview
Meriva
Бренд: Vauxhall Страницы: 2
Vauxhall Ampera Quick Reference Manual preview
Ampera
Бренд: Vauxhall Страницы: 2
Vauxhall 2012 Agila Quick Reference Manual preview
2012 Agila
Бренд: Vauxhall Страницы: 2
Vauxhall 2013 Mokka Owner'S Manual preview
2013 Mokka
Бренд: Vauxhall Страницы: 209
VBC Racing WildFire Instruction Manual preview
WildFire
Бренд: VBC Racing Страницы: 34
Vauxhall 2013 Corsa Infotainment system Quick Reference Manual preview
2013 Corsa Infotainment system
Бренд: Vauxhall Страницы: 2
Vauxhall 2010 Astra Quick Reference Manual preview
2010 Astra
Бренд: Vauxhall Страницы: 2
Vauxhall Antara Owner'S Manual preview
Antara
Бренд: Vauxhall Страницы: 236
Cadillac ESCALADE FAMILY - SPECIFICATIONS 2011 Specifications preview
ESCALADE FAMILY - SPECIFICATIONS 2011
Бренд: Cadillac Страницы: 1
BGS technic 40108 Manual preview
40108
Бренд: BGS technic Страницы: 5
Oldsmobile 1999 88 Owner'S Manual preview
1999 88
Бренд: Oldsmobile Страницы: 344
ABL eMH3 Installation Manual preview
eMH3
Бренд: ABL Страницы: 66
Audi Q3 2015 - 2019 Technical Service Bulletin preview
Q3 2015 - 2019
Бренд: Audi Страницы: 12
Ranger design 1506-PHX Cargo Plus Installation Manual preview
1506-PHX Cargo Plus
Бренд: Ranger design Страницы: 8
AUTOTECH 10.411.01.219K Installation Instructions preview
10.411.01.219K
Бренд: AUTOTECH Страницы: 1
RBO RBO4038 Product Manual preview
RBO4038
Бренд: RBO Страницы: 15

Бренды по названию

Популярные бренды

Загрузить еще бренды