Suzuki SWIFT RS415 2017 Скачать руководство пользователя страница 424

Страница: 424 / 1257

2B-14 Front Suspension:

NOTE:

• Before installing bushing, apply soap

water on its circumference to facilitate
installation.

2) Press-fit bushing (1) so that dimensions and in figure

become equal.

Suspension Control Arm / Steering Knuckle
Check

S4RS0A2206015

Inspect for cracks, deformation or damage.
If defective, replace.

Suspension Control Arm Bushing Check

S4RS0A2206016

Inspect for damage, wear or deterioration.
If defective, replace.

Suspension Control Arm Joint Check

S4RS0A2206017

• Check for smooth rotation.
• Inspect ball stud for damage.
• Inspect dust cover for damage.

NOTE:
Suspension control arm and arm joint cannot
be separated.

If there is any damage to either, control arm assembly
must be replaced as a complete unit.

(A)

(B)

I4RS0A220032-

I4RS0A220033-

I2RH01220005-

I4RS0A220035-

I4RS0A220036-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание SWIFT RS415 2017

Отзывы:

Похожие инструкции для SWIFT RS415 2017

Бренды по названию

Популярные бренды

Suzuki SWIFT RS415 2017, Руководство по обслуживанию

Результаты поиска

Содержание SWIFT RS415 2017

Отзывы:

Похожие инструкции для SWIFT RS415 2017

Бренды по названию

Популярные бренды