manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Air Bag System:  8B-117

• Check sensor (1) for dents, crack, deformation.
• Check sensor connector (sensor side and harness 

side), lock mechanism or sensor lead wire for 
damage, crack, scorching or melting.

• Check connector terminals for bent, corrosion or rust.

If any faulty condition is found in above checks, 
replace.

Passenger Air Bag (Inflator) Module Repair 
Harness Installation

S4RS0A8206027

Replace passenger air bag (inflator) module repair 
harness (4) according to the following procedure when 
the harness (1) connected with passenger air bag 
(inflator) module of the air bag harness included in 
instrument panel harness (2) and passenger air bag 
(inflator) module connector (3) is damaged.

1) Disable air bag system. Refer to “Disabling Air Bag 

System: ”.

2) Disconnect “L32” connector from floor harness 

located near the glove box.

3) Cut off passenger air bag (inflator) module harness 

(1) included in instrument panel harness (2) as 
shown, and then fasten it to instrument panel 
harness with vinyl tape for avoiding interference with 
other parts.

4) Install passenger air bag (inflator) module repair 

harness (1) to floor harness (2), instrument panel 
harness (3) and passenger air bag (inflator) module.

CAUTION:

To avoid interference with other parts, fasten 
the repair harness to instrument wire harness 
with a clamp or vinyl tape as shown in figure.

 

5) Connect each connector securely till click is heard.

5. Driver air bag (inflator) module

7. Floor harness

6. Passenger air bag (inflator) module

8. Vinyl tape

1

I4RS0A820082-

7

4

6

6

2

2

8

1

3

5

5

7

I4RS0A820103-

1

I4RS0A820083-

1

2

3

I4RS0A820085-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Ranger design 5044 Installation Manual preview
5044
Бренд: Ranger design Страницы: 6
Jeep Liberty Quick Reference Manual preview
Liberty
Бренд: Jeep Страницы: 6
Club Car Gasoline/Electric DS Golf Car 1996 Owner'S Manual preview
Gasoline/Electric DS Golf Car 1996
Бренд: Club Car Страницы: 48
Phonocar VM338 Mounting Instructions preview
VM338
Бренд: Phonocar Страницы: 6
Raptor Series MAGNUM RT Series Manual preview
MAGNUM RT Series
Бренд: Raptor Series Страницы: 6
Nuna Bugaboo turtle Instructions For Installation Manual preview
Bugaboo turtle
Бренд: Nuna Страницы: 17
Fab Fours H4550 Installation Instructions Manual preview
H4550
Бренд: Fab Fours Страницы: 13
Kia Bluetooth Phone System 2010 Reference Manual preview
Bluetooth Phone System 2010
Бренд: Kia Страницы: 16
Rostra RearSight 250-8308 Installation Instructions preview
RearSight 250-8308
Бренд: Rostra Страницы: 2
Calix group TYP MVP 823 Assembly Instructions preview
TYP MVP 823
Бренд: Calix group Страницы: 4
Alphasonik PCP15LDE Owner'S Manual preview
PCP15LDE
Бренд: Alphasonik Страницы: 8
J. Strong JST506BT Installation Instructions preview
JST506BT
Бренд: J. Strong Страницы: 2
Acura 2011 RDX Navigation System Advanced Technology Manual preview
2011 RDX Navigation System
Бренд: Acura Страницы: 16
Cadillac 2005 XLR Owner'S Manual preview
2005 XLR
Бренд: Cadillac Страницы: 438
CITROEN CX 2000 Repair Manual preview
CX 2000
Бренд: CITROEN Страницы: 394
Ford 2003 Ranger Quick Reference Manual preview
2003 Ranger
Бренд: Ford Страницы: 2
Toyota 4Runner 2020 Owner'S Manual preview
4Runner 2020
Бренд: Toyota Страницы: 596
ECS Electronics TO-245-BHU Fitting Instructions Manual preview
TO-245-BHU
Бренд: ECS Electronics Страницы: 14

Бренды по названию

Популярные бренды

Загрузить еще бренды