manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Engine General Information and Diagnosis:  1A-3

• When a malfunction is detected, engine and driving 

conditions then are stored in ECM memory as freeze 
frame data. (For the details, refer to description on 
“Freeze Frame Data: ”.)

• It is possible to communicate by using not only 

SUZUKI scan tool (2) but also OBD generic scan tool. 
(Diagnostic information can be accessed by using a 
scan tool.)

Warm-Up Cycle

A warm-up cycle means sufficient vehicle operation such 
that the coolant temperature has risen by at least 22 

q

C 

(40 

q

F) from engine starting and reaches a minimum 

temperature of 70 

q

C (160 

q

F).

Driving Cycle

A “Driving Cycle” consists of engine startup and engine 
shutoff.

2 Driving Cycle Detection Logic

The malfunction detected in the first driving cycle is 
stored in ECM memory (in the form of pending DTC) but 
the malfunction indicator lamp does not light at this time. 
It lights up at the second detection of same malfunction 
also in the next driving cycle.

Pending DTC

Pending DTC means a DTC detected and stored 
temporarily at 1 driving cycle of the DTC which is 
detected in the 2 driving cycle detection logic.

Freeze Frame Data

ECM stores the engine and driving conditions (in the 
form of data as shown in the figure) at the moment of the 
detection of a malfunction in its memory. This data is 
called “Freeze frame data”.
Therefore, it is possible to know engine and driving 
conditions (e.g., whether the engine was warm or not, 
where the vehicle was running or stopped, where air/fuel 
mixture was lean or rich) when a malfunction was 
detected by checking the freeze frame data. Also, ECM 
has a function to store each freeze frame data for three 
different malfunctions in the order as each malfunction is 
detected. Utilizing this function, it is possible to know the 
order of malfunctions that have been detected. Its use is 
helpful when rechecking or diagnosing a trouble.

3. DLC

1

2

3

I4RS0A110001-

[A]: 1st or 2nd in parentheses here represents which position in the order 

the malfunction is detected.

[A]

I3RB0A110002-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Kargo Master 80070 Assembly Lnstructions preview
80070
Бренд: Kargo Master Страницы: 13
Kargo Master 4A96L Installation Manual preview
4A96L
Бренд: Kargo Master Страницы: 21
Kargo Master 40201 Installation Manual preview
40201
Бренд: Kargo Master Страницы: 4
Chrysler Stratus LHD 1997 Interactive Electronic Service Manual preview
Stratus LHD 1997
Бренд: Chrysler Страницы: 1534
Yakima K674 Instructions Manual preview
K674
Бренд: Yakima Страницы: 13
Menabo 000081000000, Fitting Instructions Manual preview
000081000000,
Бренд: Menabo Страницы: 11
Wagan Road Ready Seat Protector User Manual preview
Road Ready Seat Protector
Бренд: Wagan Страницы: 12
Chevrolet 2016 Suburban Owner'S Manual preview
2016 Suburban
Бренд: Chevrolet Страницы: 50
Nav TV Ford 4” UNI-CAM Manual preview
Ford 4” UNI-CAM
Бренд: Nav TV Страницы: 6
Saab 2007 9-3 Remote Starter Owner'S Manual preview
2007 9-3 Remote Starter
Бренд: Saab Страницы: 304
Over Armour Offroad TX-STAMP-4-FC04 Instructions For Installation And Care preview
TX-STAMP-4-FC04
Бренд: Over Armour Offroad Страницы: 9
Rugged Ridge 11252.51 Installation Instructions preview
11252.51
Бренд: Rugged Ridge Страницы: 3
Mercedes-Benz 240 D 1979 Owner'S Manual preview
240 D 1979
Бренд: Mercedes-Benz Страницы: 91
E&G Classics Black Ice Mesh Instruction Manual preview
Black Ice Mesh
Бренд: E&G Classics Страницы: 4
Vangear Woody-Pod Instruction Manual preview
Woody-Pod
Бренд: Vangear Страницы: 5
Safe Fleet FRC SafeTrack Hardware Installation Manual preview
FRC SafeTrack
Бренд: Safe Fleet Страницы: 20
ZAPTEC ZapCharger Portable C1 User Manual preview
ZapCharger Portable C1
Бренд: ZAPTEC Страницы: 20
Saturn 2007 Ion Owner'S Manual preview
2007 Ion
Бренд: Saturn Страницы: 440

Бренды по названию

Популярные бренды

Загрузить еще бренды