manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

9C-17 Instrumentation / Driver Info. / Horn: 

Horn Inspection

S4RS0A9306029

1) Disconnect negative (–) cable at battery.
2) Remove front bumper referring to “Front Bumper 

and Rear Bumper Components:  in Section 9K”. 

3) Disconnect horn connector (1).
4) Connect battery positive (+) to terminal of horn 

connector (2) and negative (–) terminal to body 
ground.
If horn is not sounding, replace horn.

Horn Relay Inspection

S4RS0A9306028

1) Disconnect negative (–) cable at battery.
2) Remove junction block assembly referring to “BCM 

(Included in Junction Block Assembly) Removal and 
Installation:  in Section 10B”.

3) Remove horn relay (1) from junction block assembly 

(2).

4) Check that there is no continuity between terminal 

“c” and “d”. If there is continuity, replace relay.

5) Check that there is continuity between terminals “c” 

and “d” when a 12 V battery is connected to 
terminals “a” and “b”. If malfunction is found, replace 
it with a new one.

Antenna Amplifier Removal and Installation

S4RS0A9306025

NOTE:
Antenna amplifier incorporated with antenna 
base.

 

Removal

1) Remove head lining referring to “Head Lining 

Removal and Installation:  in Section 9H”.

2) Remove antenna (1) from antenna base (2).
3) Disconnect antenna feeder from antenna base (2).
4) Remove antenna base (2) from vehicle.

Installation

Reverse removal procedure noting the following.
• Tighten antenna base mounting nut to specified 

torque.

Tightening torque
Antenna base mounting nut (a):  10 N·m (1.0 kg-
m, 7.5 lb-ft)

Remote Audio Control Switch Inspection

S4RS0A9306026

1) Remove driver air bag (inflator) module referring to 

“Driver Air Bag (Inflator) Module Removal and 
Installation:  in Section 8B”.

2) Disconnect remote audio control switch connector 

from contact coil.

3) Check switch for resistance between “a” and “c” 

terminals under each condition below.
If check result is not satisfactory, replace remote 
audio control switch.

“ENTER”, “+” and “–” switch resistance
All switches released (OFF): 4700 – 5600 k

:

“ENTER” switch (1) pushing on (ON): 50 – 60 

:

“+” switch (2) pushing on (ON): 120 – 140 

:

“–” switch (3) pushing on (ON): 220 – 260 

:

1

2

I4RS0A930030-

1

2

I4RS0A930029-

b

a

c

d

c

a

d

b

I3JA01920006-

(a)

1

2

I4RH01930009-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Calira 811 Manual preview
811
Бренд: Calira Страницы: 14
Pacbrake 10475 Installation Manual preview
10475
Бренд: Pacbrake Страницы: 9
Kargo Master 40020 Assembly Manual preview
40020
Бренд: Kargo Master Страницы: 6
Daihatsu S85 Wiring Diagrams preview
S85
Бренд: Daihatsu Страницы: 41
Daihatsu S85 Workshop Manual preview
S85
Бренд: Daihatsu Страницы: 268
K&M 8494 Installation Manual preview
8494
Бренд: K&M Страницы: 3
Allen Sports QR545 Instructions preview
QR545
Бренд: Allen Sports Страницы: 2
Ford E-Transit 2022 Manual preview
E-Transit 2022
Бренд: Ford Страницы: 22
Audi Q3 2015 - 2019 Technical Service Bulletin preview
Q3 2015 - 2019
Бренд: Audi Страницы: 12
iRacing Porsche 911 GT3 R User Manual preview
Porsche 911 GT3 R
Бренд: iRacing Страницы: 25
P-Invent Troller User Manual preview
Troller
Бренд: P-Invent Страницы: 4
Kia 2014 rondo Features preview
2014 rondo
Бренд: Kia Страницы: 11
Saab 2008 9-7x Owner'S Manual preview
2008 9-7x
Бренд: Saab Страницы: 426
Vauxhall Meriva 2014 Infotainment Manual preview
Meriva 2014
Бренд: Vauxhall Страницы: 131
Honda 2006 Accord Owner'S Manual preview
2006 Accord
Бренд: Honda Страницы: 569
Volvo Ski box Installation Instructions Manual preview
Ski box
Бренд: Volvo Страницы: 7
Bulldog Security BulldogOne BD1 User Manual preview
BulldogOne BD1
Бренд: Bulldog Security Страницы: 7
TracRac TracVan Double Installation Instructions Manual preview
TracVan Double
Бренд: TracRac Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды