manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Security and Locks:  9F-3

Diagnostic Information and Procedures

Power Door Lock System Symptom Diagnosis

S4RS0A9604001

NOTE:

• Use SUZUKI scan tool makes it easy to check whether a faulty condition is on the input side or 

output side of BCM. For checking procedure, refer to “Diagnosis Using Output Test Function of 
SUZUKI Scan Tool” under “Scan Tool Data:  in Section 10B”.

• Check each part in the order from the top of the following list.

 

Power Door Lock System Operation Inspection

S4RS0A9604002

1) Check the following operation:

a) Turn the driver side key cylinder to LOCK position with door key once, check all doors lock.
b) Turn the driver side door key cylinder to UNLOCK position with door key twice, check all doors unlock.

If malfunction is found, go to “Power Door Lock System Symptom Diagnosis: ”.

Condition

Possible cause

Correction / Reference Item

All door can not be locked 
/ unlocked by all of 
switches

Circuit fuse blown

Replace fuse and check for short circuit.

Wiring or grounding faulty

Repair circuit.

BCM faulty

Replace after making sure that none of above 
parts is faulty.

All door can not be locked 
/ unlocked by only power 
door lock switch

Circuit fuse blown

Replace fuse and check for short circuit.

Power door lock switch faulty

Check power door lock switch referring to 
“Power Door Lock Switch Inspection: ”.

Wiring harness connected to power door 
lock switch faulty

Repair.

Wiring or grounding faulty

Repair circuit.

BCM faulty

Replace after making sure that none of above 
parts is faulty.

All door can not be locked 
/ unlocked by only key 
cylinder switch

Circuit fuse blown

Replace fuse and check for short circuit.

Key cylinder switch faulty

Check key cylinder switch referring to “Door 
Key Cylinder Switch Inspection: ”.

Wiring or grounding faulty

Repair circuit.

BCM faulty

Replace after making sure that none of above 
parts is faulty.

Only one door can not be 
locked / unlocked

Power door lock actuator faulty

Check actuator referring to “Power Door Lock 
Actuator Inspection: ”.

Wiring harness connected to applicable 
door lock actuator faulty

Repair.

BCM faulty

Replace after making sure that none of above 
parts is faulty.

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Wagan 2591 User Manual preview
2591
Бренд: Wagan Страницы: 12
Ultra Start KE-6 Owner'S Manual preview
KE-6
Бренд: Ultra Start Страницы: 8
Westin 23-3130 Instructions preview
23-3130
Бренд: Westin Страницы: 3
DEFA WarmUp 411702 Fitting Instructions Manual preview
WarmUp 411702
Бренд: DEFA Страницы: 9
rough country Slim Line LED Light Grille Kit Manual preview
Slim Line LED Light Grille Kit
Бренд: rough country Страницы: 8
Audi A4 2016 Quick Questions And Answers preview
A4 2016
Бренд: Audi Страницы: 9
Belkin WIC004 Setting Up preview
WIC004
Бренд: Belkin Страницы: 4
Prorack K544 Fitting Instructions Manual preview
K544
Бренд: Prorack Страницы: 20
Safe Fleet PRIME DESIGN VBI-FT21B Manual preview
PRIME DESIGN VBI-FT21B
Бренд: Safe Fleet Страницы: 12
Honda Plusone Console 4521011B User Information preview
Plusone Console 4521011B
Бренд: Honda Страницы: 4
Cadillac 2004 ESCALADE Customer Convenience/Personalization Manual preview
2004 ESCALADE
Бренд: Cadillac Страницы: 20
Vauxhall Meriva 2014 Infotainment Manual preview
Meriva 2014
Бренд: Vauxhall Страницы: 131
TATA Motors Indigo eCS Owner'S Manual & Service Book preview
Indigo eCS
Бренд: TATA Motors Страницы: 166
Advanced Diagnostics MVP PRO Manual preview
MVP PRO
Бренд: Advanced Diagnostics Страницы: 10
Club Car TransPorter 4 Maintenance And Service Manual preview
TransPorter 4
Бренд: Club Car Страницы: 286
Thule Kit 1312 Instructions Manual preview
Kit 1312
Бренд: Thule Страницы: 8
Huf HUF8432MS Technical Description And User Manual preview
HUF8432MS
Бренд: Huf Страницы: 6
Yakima Landing Pad 11 Manual preview
Landing Pad 11
Бренд: Yakima Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды