manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Aux. Emission Control Devices:  1B-2

ii) Turn ON ignition switch, clear DTC and 

select “MISC TEST” mode on SUZUKI scan 
tool.

Special tool
(A):  SUZUKI scan tool

b) When not using SUZUKI scan tool:

NOTE:
Before performed this check, be sure to read 
the “Precautions of ECM Circuit Inspection:  
in Section 1A”.

 

i)

Disconnect purge valve vacuum hoses from 
intake manifold and EVAP canister.

ii) Remove ECM from its bracket with ECM 

connectors connected referring to “Engine 
Control Module (ECM) Removal and 
Installation:  in Section 1C”.

iii) Connect special tool between ECM and ECM 

connector referring to “Inspection of ECM 
and Its Circuits:  in Section 1A”.

iv) Turn ON ignition switch.

Using service wire, ground “C37-29” terminal 
circuit of special tool (valve ON: “B”) and 
unground it (valve OFF: “A”).

2) Check purge valve for operation and vacuum 

passage for clog when valve is switched ON and 
OFF by using SUZUKI scan tool or service wire.
If check result is not satisfactory, check vacuum 
hoses, EVAP canister purge valve, wire harness and 
connections.

EVAP canister purge valve specification
[A] Valve OFF: When vacuum (–60 kPa (–8.7 psi)) 
is applied to hose (1), vacuum can be applied.
[B] Valve ON: When vacuum is applied to hose 
(1), vacuum can not be applied.

Special tool
(A):  09917–47011

Vacuum Passage Inspection

S4RS0A1206003

Start engine and run it at idle speed. Disconnect vacuum 
hose (1) from EVAP canister purge valve (2). With finger 
placed against disconnected hose, check that vacuum is 
applied.
If it is not applied, clean vacuum passage by blowing 
compressed air.

(A)

1

I4RS0A120003-

“C37-29”

“A”

“B”

I4RS0A120004-

[A]

[B]

1

(A)

1

(A)

I3RB0A120005-

I3RM0A120006-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Cadillac ESCALADE - BROCHURE 2009 Personalization Manual preview
ESCALADE - BROCHURE 2009
Бренд: Cadillac Страницы: 24
Cadillac Escalade Personalization Manual preview
Escalade
Бренд: Cadillac Страницы: 20
Cadillac Escalade 2016 Convenience/Personalization Manual preview
Escalade 2016
Бренд: Cadillac Страницы: 20
Fabbri BICI OK 2 Quick Start Manual preview
BICI OK 2
Бренд: Fabbri Страницы: 4
Carax HUD CRX-3001 Quick Start Manual preview
HUD CRX-3001
Бренд: Carax Страницы: 2
Metra Electronics 99-3103 Installation Instructions preview
99-3103
Бренд: Metra Electronics Страницы: 2
Roadmaster Sterling ALL-TERRAIN 576 Owner'S Manual & Installation Instructions preview
Sterling ALL-TERRAIN 576
Бренд: Roadmaster Страницы: 12
Wagan Road Ready Seat Protector User Manual preview
Road Ready Seat Protector
Бренд: Wagan Страницы: 12
Chevrolet 2016 Suburban Owner'S Manual preview
2016 Suburban
Бренд: Chevrolet Страницы: 50
Opel 2011 Insignia Owner'S Manual preview
2011 Insignia
Бренд: Opel Страницы: 254
MAcarbon Ferrari 360 Map Carbon Light Installation Instructions preview
Ferrari 360 Map Carbon Light
Бренд: MAcarbon Страницы: 4
Westin 22-1065 Instructions preview
22-1065
Бренд: Westin Страницы: 3
Jaeger 12020523 Fitting Instructions Manual preview
12020523
Бренд: Jaeger Страницы: 11
Honda 1991 Civic Online Reference Owner'S Manual preview
1991 Civic
Бренд: Honda Страницы: 124
Havis C-DMM-3005 Installation Instructions preview
C-DMM-3005
Бренд: Havis Страницы: 5
Atera 080 705 User Information preview
080 705
Бренд: Atera Страницы: 3
Black Horse RB001BK Installation Instructions preview
RB001BK
Бренд: Black Horse Страницы: 5
Maserati Grecale 2023 Owner'S Manual preview
Grecale 2023
Бренд: Maserati Страницы: 302

Бренды по названию

Популярные бренды

Загрузить еще бренды