manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

1E-3 Engine Lubrication System: 

Diagnostic Information and Procedures

Oil Pressure Check

S4RS0A1504001

NOTE:
Prior to checking oil pressure, check the 
following.
• Oil level in oil pan

If oil level is low, add oil up to Full level 
mark (hole) (1) on oil level gauge referring 
to “Engine Oil and Filter Change:  in 
Section 0B”.

• Oil quality

If oil is discolored or deteriorated, change 
it. For particular oil to be used, refer to 
“Engine Oil and Filter Change:  in Section 
0B”.

• Oil leaks

If leak is found, repair it.

 

1) Remove front bumper referring to “Front Bumper 

and Rear Bumper Components:  in Section 9K”.

2) Remove engine front cover (1).

3) Disconnect oil pressure switch coupler (1).
4) Remove oil pressure switch (2) from cylinder block.

5) Install special tools (oil pressure gauge) to vacated 

threaded hole of oil pressure switch.

Special tool
(A):  09915–77310
(B):  09915–78211

6) Start engine and warm engine up to normal 

operating temperature.

NOTE:
Be sure to shift transaxle gear shift lever in 
“Neutral” (shift select lever in “P” range for 
A/T vehicle), set parking brake and block 
drive wheels.

 

7) After warming up, raise engine speed to 4,000 r/min. 

and measure oil pressure.

Oil pressure specification
More than 270 kPa (2.7 kg/cm

2

, 39.8 psi) at 4,000 

r/min. (rpm)

8) After checking oil pressure, stop engine and remove 

oil pressure gauge and attachment.

2. Low level mark (hole)

I2RH0B150002-

1

I4RS0A150001-

I2RH0B150003-

I2RH0B150004-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

GMC HUMMER EV 2022 Manual preview
HUMMER EV 2022
Бренд: GMC Страницы: 140
U.S. General 97845 Set Up And Operating Instructions preview
97845
Бренд: U.S. General Страницы: 5
UltraGauge EM Installation & Operation Manual preview
EM
Бренд: UltraGauge Страницы: 55
Blue Giant STRONGARM RVR303 Installation & Technical Manual preview
STRONGARM RVR303
Бренд: Blue Giant Страницы: 48
Buick 2005 Terraza Owner'S Manual preview
2005 Terraza
Бренд: Buick Страницы: 428
Menabo DELTA DL FIX 209FP Fitting Instructions Manual preview
DELTA DL FIX 209FP
Бренд: Menabo Страницы: 8
Safe Fleet PRIME DESIGN HXR-269-E-UM3-80 Manual preview
PRIME DESIGN HXR-269-E-UM3-80
Бренд: Safe Fleet Страницы: 12
RAM Truck 2014 Owner'S Manual preview
Truck 2014
Бренд: RAM Страницы: 330
Thule 145012 Quick Start Manual preview
145012
Бренд: Thule Страницы: 2
Soundoff Signal nERGY ETSA200R-PA Quick Start Manual preview
nERGY ETSA200R-PA
Бренд: Soundoff Signal Страницы: 3
Truma Mover H SE User Manual preview
Mover H SE
Бренд: Truma Страницы: 10
Seat Toledo 2019 Owner'S Manual preview
Toledo 2019
Бренд: Seat Страницы: 300
Tuff Tonneaus Bunji Ute Installation Instructions preview
Bunji Ute
Бренд: Tuff Tonneaus Страницы: 4
CITROËN c4 picasso 2006 Owner'S Manual preview
c4 picasso 2006
Бренд: CITROËN Страницы: 266
Federal Signal Corporation LEDTCL97 Installation And Service Instructions Manual preview
LEDTCL97
Бренд: Federal Signal Corporation Страницы: 12
AVS Ventvisor Installation Instructions Manual preview
Ventvisor
Бренд: AVS Страницы: 9
Volkswagen Transporter T5 Manuallines preview
Transporter T5
Бренд: Volkswagen Страницы: 83
Toyota PT427-48080 Installation Instructions Manual preview
PT427-48080
Бренд: Toyota Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды