manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

0B-3 Maintenance and Lubrication: 

NOTE:

• “I”: Inspect and correct or replace if necessary
• “R”: Replace or change
• *1: Inspect more frequently if the vehicle is used under dusty conditions.
• *2: Clean or replace more frequently if the air from the air conditioning decreases.

 

Repair Instructions

Accessory Drive Belt Inspection

S4RS0A0206001

WARNING:

All inspection and replacement are to be 
performed with ENGINE NOT RUNNING.

 

Water Pump and Generator Drive Belt

1) Disconnect negative (–) cable at battery.
2) Inspect belt for cracks, cuts, deformation, wear and 

cleanliness. If any defect exists, replace.
Check belt for tension.

Water pump and generator belt tension
“a”: 4.5 – 5.5 mm (0.18 – 0.22 in.) deflection 
under 100 N (10 kg, 22 lb) pressure

NOTE:
When replacing belt with a new one, adjust 
belt tension to 3 – 4 mm (0.12 – 0.16 in.)

 

3) If belt is too tight or too loose, adjust it to 

specification by adjusting alternator position.

4) Tighten alternator adjusting bolts and pivot bolt.
5) Connect negative (–) cable to battery.

A/C Compressor Drive Belt (If Equipped)

1) Disconnect negative (–) cable at battery.
2) Inspect belt for cracks, cuts, deformation, wear and 

cleanliness. If any defect exists, replace.
Check belt for tension.
If belt tension is out of specification, adjust it 
referring to “Compressor Drive Belt Inspection and 
Adjustment:  in Section 7B”.

A/C compressor drive belt tension
“a”: 7 – 8 mm (0.28 – 0.31 in.) deflection under 
100 N (10 kg, 22 lb) pressure

– B – – E – – H

Manual transaxle oil

)

 R

First time only:
15,000 km (9,000 miles) or 12 months
Second time and after:
Every 30,000 km (18,000 miles) or 24 
months reckoning from 0 km (0 mile) 
or 0 month

– B – – E – – H

Automatic transaxle fluid

)

 R

Every 30,000 km (18,000 miles) or 24 
months

– – C D – – – –

Air conditioning filter *2

)

 I

Every 15,000 km (9,000 miles) or 12 
months

)

 R

Every 45,000 km (27,000 miles) or 36 
months

Severe 

condition code

Maintenance

Maintenance 

operation

Maintenance interval

I3RM0A020001-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

RaceChip XLR User Manual preview
XLR
Бренд: RaceChip Страницы: 20
Ecco Vantage 12 Series Installation And Operation Instructions preview
Vantage 12 Series
Бренд: Ecco Страницы: 5
Nuna Bugaboo turtle Instructions For Installation Manual preview
Bugaboo turtle
Бренд: Nuna Страницы: 17
FALCON RIDGE BC-3400-FC05 Instructions For Installation And Care preview
BC-3400-FC05
Бренд: FALCON RIDGE Страницы: 7
Volvo 2004 C70 HPT User Manual preview
2004 C70 HPT
Бренд: Volvo Страницы: 30
Safe Fleet PRIME DESIGN VBI-FT21B Manual preview
PRIME DESIGN VBI-FT21B
Бренд: Safe Fleet Страницы: 12
Honda Plusone Console 4521011B User Information preview
Plusone Console 4521011B
Бренд: Honda Страницы: 4
U.S. General 96524 Set Up And Operating Instructions Manual preview
96524
Бренд: U.S. General Страницы: 8
Buick 2015 LaCrosse Getting To Know Manual preview
2015 LaCrosse
Бренд: Buick Страницы: 20
EUFAB 16458 Operating Instructions Manual preview
16458
Бренд: EUFAB Страницы: 16
TEINHOF V-295 Fitting And Operation Manual preview
V-295
Бренд: TEINHOF Страницы: 2
Mitsubishi MOTORS OUTLANDER PHEV 2022 Manual preview
OUTLANDER PHEV 2022
Бренд: Mitsubishi MOTORS Страницы: 8
Honda 2000 RL Owner'S Manual preview
2000 RL
Бренд: Honda Страницы: 330
Discount Car Stereo A2DIY-JAG98 Quick Start Manual preview
A2DIY-JAG98
Бренд: Discount Car Stereo Страницы: 11
Whispbar K408W Fitting Instructions Manual preview
K408W
Бренд: Whispbar Страницы: 15
Blue Bird TC/2000 Owner'S Manual preview
TC/2000
Бренд: Blue Bird Страницы: 111
BMW 316I Owner'S Handbook Manual preview
316I
Бренд: BMW Страницы: 177
Volvo FH 6X2 Specifications preview
FH 6X2
Бренд: Volvo Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды