manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Heater and Ventilation:  7A-11

4) Remove passenger air bag module from instrument 

panel referring to “Passenger Air Bag (Inflator) 
Module Removal and Installation:  in Section 8B”.

5) Separate left side ventilation louver (1) and 

passenger air bag module (2).

Installation

Reverse removal procedure noting the following 
instruction.
• Left side ventilation louver is fitted to passenger air 

bag module with four clips (1). When installing left 
side ventilation louver to passenger air bag module, 
position the smallest clip to the top.

Air Filter Removal and Installation

S4RS0A7106023

Removal

1) Remove glove box from instrument panel.
2) Remove air filter cover (1) from HVAC unit.

3) Pull out air filter from HVAC unit.

Installation

Reverse removal procedure noting the following 
instructions.
• Position air filter by directing its arrow mark to the 

upward.

• Fit air filter cover (1) to HVAC unit so as not to stick air 

filter (2) by air filter cover’s claw (3). Otherwise, air 
filter is deformed and loses its functionality.

Air Filter Cleaning

S4RS0A7106022

Blow compressed air to the air outlet side of air filter.

2

1

I4RS0A710027-

1

I4RS0A710028-

1

I4RS0A710029-

I4RS0A710030-

1

3

2

1

3

I4RS0A710031-

I4RS0A710032-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Jeep 2014 Wrangler Owner'S Manual preview
2014 Wrangler
Бренд: Jeep Страницы: 673
Prorack K383 Fitting Instructions Manual preview
K383
Бренд: Prorack Страницы: 14
Bestop 54822 Installation Instructions Manual preview
54822
Бренд: Bestop Страницы: 11
Whispbar K455W Fitting Instructions Manual preview
K455W
Бренд: Whispbar Страницы: 14
Vauxhall 2014 Insignia VXR SuperSport Specifications preview
2014 Insignia VXR SuperSport
Бренд: Vauxhall Страницы: 56
Safe Fleet RVS-218627 Instruction Manual preview
RVS-218627
Бренд: Safe Fleet Страницы: 38
Toyota AURION 2013 Owner'S Manual preview
AURION 2013
Бренд: Toyota Страницы: 371
Safe Fleet PRIME DESIGN VBI-FT21B Manual preview
PRIME DESIGN VBI-FT21B
Бренд: Safe Fleet Страницы: 12
Honda Plusone Console 4521011B User Information preview
Plusone Console 4521011B
Бренд: Honda Страницы: 4
AEM 30-3500 Instruction Manual preview
30-3500
Бренд: AEM Страницы: 27
APS IA06SJD4B Installation Instructions preview
IA06SJD4B
Бренд: APS Страницы: 3
Cadillac 2000 Escalade Manual preview
2000 Escalade
Бренд: Cadillac Страницы: 339
EZ-ON 100SMU Quick Start Manual preview
100SMU
Бренд: EZ-ON Страницы: 2
Kargo Master PRO-IV Assembly Instructions Manual preview
PRO-IV
Бренд: Kargo Master Страницы: 8
Chevrolet 2012 Malibu Owner'S Manual preview
2012 Malibu
Бренд: Chevrolet Страницы: 376
BENDIX C-5 CUT OUT COCK Manual preview
C-5 CUT OUT COCK
Бренд: BENDIX Страницы: 2
Thule 1325 Kit Instructions Manual preview
1325 Kit
Бренд: Thule Страницы: 8
Directed 403.NISS4HT 2.36 RSR Installation Manual preview
403.NISS4HT 2.36 RSR
Бренд: Directed Страницы: 22

Бренды по названию

Популярные бренды

Загрузить еще бренды