manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

9J-6 Hood / Fenders / Doors: 

WARNING:

Handling of Rear End Door Balancer 
(Damper)
• Handle balancer carefully. Do not scar or 

scratch exposed surface of its piston rod, 
and never allow any paint or oil to stick to 
its surface.

• Do not turn piston rod with balancer fully 

extended.

• Do not disassemble balancer (1) because 

its cylinder is filled with gas.

Discarding of Rear End Door Balancer 
(Damper)
• The gas itself in balancer is harmless but it 

may issue out of the hole together with 
chips generated by the drill (2). Therefore, 
be sure to wear goggle when drilling.

• Using a 2 to 3 mm (0.08 to 0.12 in.) drill (2), 

make a hole to remove gas inside as 
shown before discarding.

 

Installation

Reverse removal procedure noting the following.
• Tighten rear end door balancer bolt to specified 

torque.

Tightening torque
Rear end door balancer bolt (a):  23 N·m (2.3 kg-
m, 17.0 lb-ft)

• Secure wiring harness (1).

• Adjust door latch striker position by referring to “Rear 

End Door Lock Assembly Removal and Installation:  
in Section 9F”.

• Adjust door cushion so that door contacts body when 

closed.

• Apply sealant to contact face “A” of door hinge (1) and 

apply grease to rotating part “B” of hinge (1).
Specified sealant and grease.

“A”:  Sealant 99000–31110
“B”:  Grease 99000–25010

I2RH019A0010-

(a)

(a)

I4RS0A9A0013-

1

I4RS0A9A0012-

I2RH019A1012-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

ZAPTEC Go Instruction Manual preview
Go
Бренд: ZAPTEC Страницы: 240
Saab 99 Important Operatlng, Safety And Maintenance Instructions preview
99
Бренд: Saab Страницы: 75
Kargo Master 40020 Assembly Manual preview
40020
Бренд: Kargo Master Страницы: 6
Neuspeed 25.02.22.2 Installation Instructions preview
25.02.22.2
Бренд: Neuspeed Страницы: 2
BMW Wireless Charging Station Universal Instructions For Use Manual preview
Wireless Charging Station Universal
Бренд: BMW Страницы: 160
Hama 00178266 Operating Instruction preview
00178266
Бренд: Hama Страницы: 75
Safe Fleet RVS-082550 Instruction Manual preview
RVS-082550
Бренд: Safe Fleet Страницы: 11
Camec 042374 User Manual preview
042374
Бренд: Camec Страницы: 19
Tachosys digidl Installation Manual preview
digidl
Бренд: Tachosys Страницы: 28
Scion 2012 iQ Quick Reference Manual preview
2012 iQ
Бренд: Scion Страницы: 24
v.link NAL-PC-HSD Manual preview
NAL-PC-HSD
Бренд: v.link Страницы: 21
Jeep Grand Cherokee SRT 2019 Owner'S Manual preview
Grand Cherokee SRT 2019
Бренд: Jeep Страницы: 656
Safe Fleet PRIME DESIGN HRR3-E-PM42 Manual preview
PRIME DESIGN HRR3-E-PM42
Бренд: Safe Fleet Страницы: 12
N.R. AUTOSEATS Top User Manual preview
Top
Бренд: N.R. AUTOSEATS Страницы: 8
V8 equipment E.BEX Manual preview
E.BEX
Бренд: V8 equipment Страницы: 34
Ranger design 1525-PCX Installation Manual preview
1525-PCX
Бренд: Ranger design Страницы: 22
Nugent Tipper Remote Kit User Manual preview
Tipper Remote Kit
Бренд: Nugent Страницы: 21
Edelbrock 67312 Installation Instructions preview
67312
Бренд: Edelbrock Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды