manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Brake Control System and Diagnosis:  4A-16

Brake Booster Inspection and Adjustment

S4RS0A4106018

Installation Position of Push Rod

If push rod clevis (1) has been removed, adjust distance 
between booster installation surface (without including 
packing) and the center of clevis pin hole to standard 
value “a” and tighten nut (a) to specified torque.

Distance “a” between center of booster clevis pin 
hole and booster surface
Standard:
114.5 – 115.5 mm (4.51 – 4.54 in.)

Tightening torque
Clevis lock nut (a):  15 N·m (1.5 kg-m, 11.0 lb-ft)

Specifications

Tightening Torque Specifications

S4RS0A4107001

NOTE:
The specified tightening torque is also described in the following.
“Front Brake Hose / Pipe Construction: ”
“Master Cylinder Components: ”
“Brake Booster Components: ”

 

Reference:

For the tightening torque of fastener not specified in this section, refer to “Fasteners Information:  in Section 0A”.

Special Tools and Equipment

Recommended Service Material

S4RS0A4108001

NOTE:
Required service material is also described in the following.
“Master Cylinder Components: ”

 

I4RS0A410022-

Fastening part

Tightening torque

Note

N

˜

m

kg-m

lb-ft

Front brake caliper bleeder plug

8.0

0.8

6.0

)

Rear wheel cylinder bleeder plug

7.5

0.75

5.5

)

Reservoir bolt

2.5

0.25

2.0

)

Master cylinder fixing nut

15

1.5

11.0

)

Brake pipe flare nut

16

1.6

11.5

)

Booster mounting nut

13

1.3

9.5

)

Brake pedal bracket mounting bolt

13

1.3

9.5

)

Clevis lock nut

15

1.5

11.0

)

Material

SUZUKI recommended product or Specification

Note

Brake fluid

DOT 3

—

(DOT 3) 

)

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

JETBAG 320 Fitting Instructions Manual preview
320
Бренд: JETBAG Страницы: 44
Horn Tools HISDMSPTRA01 Mounting Instructions preview
HISDMSPTRA01
Бренд: Horn Tools Страницы: 6
Saab 32 025 888 Installation Instructions preview
32 025 888
Бренд: Saab Страницы: 3
KRAFTWERK Automotive 31006 Instructions preview
Automotive 31006
Бренд: KRAFTWERK Страницы: 2
Honda 2010 Pilot Technology Reference Manual preview
2010 Pilot
Бренд: Honda Страницы: 20
Kia 2009 Rio Series Owner'S Manual preview
2009 Rio Series
Бренд: Kia Страницы: 219
Renault ALASKAN 2017 Driver'S Handbook Manual preview
ALASKAN 2017
Бренд: Renault Страницы: 340
walser ULTIMATE SPEED 296713 Assembly And Safety Advice preview
ULTIMATE SPEED 296713
Бренд: walser Страницы: 10
Mercedes-Benz 2009 E-Class Manual preview
2009 E-Class
Бренд: Mercedes-Benz Страницы: 373
ConWys AG 21500598C VW Fitting Instructions Manual preview
21500598C VW
Бренд: ConWys AG Страницы: 16
Linear Logic scangauge2 Quick Start Manual preview
scangauge2
Бренд: Linear Logic Страницы: 8
Webasto Telestart T70 Installation Instructions Manual preview
Telestart T70
Бренд: Webasto Страницы: 23
Carcomm CMPC-22 Fujitsu-Siemens PocketLoox 410 Installation Manual preview
CMPC-22 Fujitsu-Siemens PocketLoox 410
Бренд: Carcomm Страницы: 2
PUTCO 1951 Series Instruction Manual preview
1951 Series
Бренд: PUTCO Страницы: 3
Brink 5978 Fitting Instructions Manual preview
5978
Бренд: Brink Страницы: 21
Reliant ROBIN 850 Workshop Manual preview
ROBIN 850
Бренд: Reliant Страницы: 206
Sintrones SBOX-2320 User Manual preview
SBOX-2320
Бренд: Sintrones Страницы: 55
Curt Group Aries AL235045 Installation Manual preview
Aries AL235045
Бренд: Curt Group Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды