manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

1K-4 Exhaust System: 

4) Install new seal ring and connect exhaust No.1 pipe 

(1) to exhaust No.2 pipe. Tighten pipe fasteners to 
specified torque.

Tightening torque
Exhaust No.2 pipe bolt (c):  43 N·m (4.3 kg-m, 
31.0 lb-ft)

5) Install heated oxygen sensors (3) referring to 

“Exhaust System Components: ”, if removed.

NOTE:
Be sure to identify heated oxygen sensor 
No.1 and No.2 by its connector color.

 

6) Connect heated oxygen sensor No.1 connector (1) 

(connector color: green) and heated oxygen sensor 
No.2 connector (2) (connector color: gray), and then 
fit coupler to bracket securely.

7) Install A/C condenser to vehicle body for equipped 

with A/C.

8) Install radiator referring to “Radiator Removal and 

Installation:  in Section 1F” for equipped with A/C.

9) Install front bumper with front grille by referring to 

“Front Bumper and Rear Bumper Components:  in 
Section 9K”.

10) Connect negative cable at battery.

11) Check exhaust system for exhaust gas leakage.

Exhaust Pipe and Muffler Removal and 
Installation

S4RS0A1B06004

For replacement of exhaust pipe, be sure to hoist vehicle 
and observe WARNING under “Exhaust System 
Components: ” and the following.

CAUTION:

Exhaust manifold have three way catalytic 
converter in it, it should not be exposed to 
any impulse.
Be careful not to drop it or hit it against 
something.

 

• Tighten bolts and nuts to specified torque when 

reassembling. Refer to “Exhaust System 
Components: ”.

• After installation, start engine and check each joint of 

exhaust system for leakage.

2

(b)

(a)

1

(C)

3

I4RS0A1B0005-

1

2

I4RS0A1B0006-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Calix M5T 187A Assembly Instructions preview
M5T 187A
Бренд: Calix Страницы: 5
Warrior Products 4560 Manual preview
4560
Бренд: Warrior Products Страницы: 4
Buick 2005 Terraza Owner'S Manual preview
2005 Terraza
Бренд: Buick Страницы: 428
Ford FIESTA ST 2019 Supplement Manual preview
FIESTA ST 2019
Бренд: Ford Страницы: 37
Dometic PERFECTVIEW CAM80AHD Installation And Operating Manual preview
PERFECTVIEW CAM80AHD
Бренд: Dometic Страницы: 196
AutoWatch 457 Rli Wiring Diagram preview
457 Rli
Бренд: AutoWatch Страницы: 4
Marlon Xplore Pro II SxS Owner’S Manual Assembly & Installation Instructions preview
Xplore Pro II SxS
Бренд: Marlon Страницы: 15
Hyundai Santa Fe 2019 Getting Started Manual preview
Santa Fe 2019
Бренд: Hyundai Страницы: 18
THIEYE CarView 2 User Manual preview
CarView 2
Бренд: THIEYE Страницы: 88
Carcomm CHFS-34 HTC Installation Manual preview
CHFS-34 HTC
Бренд: Carcomm Страницы: 2
travall TDG 1486 Fitting Instructions preview
TDG 1486
Бренд: travall Страницы: 4
true-i HMBS-200 User Manual preview
HMBS-200
Бренд: true-i Страницы: 11
Ford Escape 2022 Owner'S Manual preview
Escape 2022
Бренд: Ford Страницы: 585
Jaeger 21260514J Fitting Instructions Manual preview
21260514J
Бренд: Jaeger Страницы: 11
ATS 664-0030 Installation And Operating Manual preview
664-0030
Бренд: ATS Страницы: 12
Cadillac 2011 Cadillac Owner Assistance Information preview
2011 Cadillac
Бренд: Cadillac Страницы: 48
Buick 1997 Park Avenue Manual preview
1997 Park Avenue
Бренд: Buick Страницы: 420
Yakima FreshSesh PowderHound Manual preview
FreshSesh PowderHound
Бренд: Yakima Страницы: 18

Бренды по названию

Популярные бренды

Загрузить еще бренды