Suzuki SWIFT RS415 2017 Скачать руководство пользователя страница 386

Страница: 386 / 1257

Starting System: 1I-8

• Check the commutator and armature core. If there is

continuity, the armature is grounded and must be
replaced.

• Check for continuity between segments. If there is no

continuity at any test point, there is an open circuit
and the armature must be replaced.

Gears

Inspect the internal gear and the planetary gears for
wear, damage or other abnormal conditions. Replace if
necessary.

Pinion and Over-Running Clutch

• Inspect the pinion for wear, damage or other abnormal

conditions.
Check that clutch locks up when turned in direction of
drive and rotates smoothly in reverse direction.
Replace if necessary.

• Inspect the spline teeth for wear or damage. Replace

if necessary.
Inspect the pinion for smooth movement.

Front Housing Bush

Inspect the bush for wear or damage. Replace if
necessary.

I2RH01190019-

I2RH01190020-

I2RH01190021-

I2RH01190022-

I2RH01190023-

I2RH01190024-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание SWIFT RS415 2017

Отзывы:

Похожие инструкции для SWIFT RS415 2017

Бренды по названию

Популярные бренды

Suzuki SWIFT RS415 2017, Руководство по обслуживанию

Результаты поиска

Содержание SWIFT RS415 2017

Отзывы:

Похожие инструкции для SWIFT RS415 2017

Бренды по названию

Популярные бренды