manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Wheels and Tires:  2D-5

Repair Instructions

General Balance Procedures

S4RS0A2406001

Deposits of mud, etc. must be cleaned from inside of rim.

WARNING:

Stones should be removed from the tread in 
order to avoid operator injury during spin 
balancing and to obtain good balance.

 

Each tire should be inspected for any damage, then 
balanced according to equipment manufacturer’s 
recommendation.

Off-Vehicle Balancing

Most electronic off-vehicle balancers are more accurate 
than the on-vehicle spin balancers. They are easy to use 
and give a dynamic (two plane) balance. Although they 
do not correct for drum or disc unbalance as does on-
vehicle spin balancing, this is overcome by their 
accuracy, usually to within 1/8 ounce.

On-Vehicle Balancing

On-vehicle balancing methods vary with equipment and 
tool manufacturers. Be sure to follow each 
manufacturer’s instructions during balancing operation.

WARNING:

Wheel spin should be limited to 35 mph (55 
km/h) as indicated on speedometer.
This limit is necessary because speedometer 
only indicates one-half of actual wheel speed 
when one drive wheel is spinning and the 
other drive wheel is stopped.
Unless care is taken in limiting drive wheel 
spin, spinning wheel can reach excessive 
speeds. This can result in possible tire 
disintegration or differential failure, which 
could cause serious personal injury or 
extensive vehicle damage.

 

CAUTION:

For vehicle equipped with ABS, using on-
vehicle balancing method with ignition 
switch ON may set malfunction diagnostic 
trouble code (DTC) of ABS even when system 
is in good condition.
Never turn ignition switch ON while spinning 
wheel.

 

Tire Rotation

S4RS0A2406002

To equalize wear, rotate tires according to figure. Radial 
tires should be rotated periodically. Set tire pressure.

NOTE:
Due to their design, radial tires tend to wear 
faster in the shoulder area, particularly in 
front positions. This makes regular rotation 
especially necessary.

 

[A]: 5-tire rotation

NOTE:
Applicable to vehicles equipped with 5 
tires including spare tire all of which are 
identical in size

 

[B]: 4-tire rotation

LH: Left-hand drive

RH: Right-hand drive

I3RH0A240001-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Alpine eX-10 Installation Manual preview
eX-10
Бренд: Alpine Страницы: 8
Dynojet 24xLC2 Linx Installation Manual preview
24xLC2 Linx
Бренд: Dynojet Страницы: 68
Kuda-Phonebase 283410 Installation Instruction preview
283410
Бренд: Kuda-Phonebase Страницы: 3
femkes Hopper on Top User Manual preview
Hopper on Top
Бренд: femkes Страницы: 7
Waeco 8885100124 Operating Manual preview
8885100124
Бренд: Waeco Страницы: 172
VBG 56-201901 Mounting Instructions preview
56-201901
Бренд: VBG Страницы: 16
Fiat Fiat Bravo LPG Owner'S Manual preview
Fiat Bravo LPG
Бренд: Fiat Страницы: 24
Valeo AS1A Owner'S Manual preview
AS1A
Бренд: Valeo Страницы: 28
Vauxhall Astra 2021 Owner'S Manual preview
Astra 2021
Бренд: Vauxhall Страницы: 259
Omix-Ada Alloy Rugged Ridge X-Clamp Manual preview
Alloy Rugged Ridge X-Clamp
Бренд: Omix-Ada Страницы: 2
Dodge 8W-70 Wiring Diagram preview
8W-70
Бренд: Dodge Страницы: 3
Bestop 51252 Installation Instructions preview
51252
Бренд: Bestop Страницы: 4
Roadmaster 195125 Assembly And Operating Instructions preview
195125
Бренд: Roadmaster Страницы: 4
Safe Fleet Prime Design OCM-3032 Quick Start Manual preview
Prime Design OCM-3032
Бренд: Safe Fleet Страницы: 4
Fabbri BICI OK 2 Manual preview
BICI OK 2
Бренд: Fabbri Страницы: 32
Whelen Engineering Company SAK34 Installation Manual preview
SAK34
Бренд: Whelen Engineering Company Страницы: 2
Aries 2051182 Installation Manual preview
2051182
Бренд: Aries Страницы: 3
Easee Base 1-Way User Manual / Installation Manual preview
Base 1-Way
Бренд: Easee Страницы: 21

Бренды по названию

Популярные бренды

Загрузить еще бренды