manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

2D-4 Wheels and Tires: 

Equipment manufacture’s recommendations

Radial Tire Lead / Pull Description

S4RS0A2401006

“Lead / Pull” is the deviation of the vehicle from a straight 
path on a level road even with no pressure on the 
steering wheel.
Lead is usually caused by the following conditions.
• Improper tire and wheel alignment.
• Uneven brake assemblies.
• Tire construction.
The way in which a tire is built can produce lead in a 
vehicle. An example of this is placement of the belt. Off 
center belts on radial tires can cause the tire to develop 
a side force while rolling straight down the road. If one 
side of the tire has a little larger diameter than the other, 
the tire will tend to roll to one side. This will develop a 
side force which can produce vehicle lead.
The procedure in the figure (Lead Diagnosis) should be 
used to make sure that wheel alignment is not mistaken 
for tire lead.
• Part of the lead diagnosis procedure is different from 

the proper tire rotation pattern currently in the owner 
and service manuals. If a medium to high mileage tire 
is moved to the other side of the vehicle, be sure to 
check that ride roughness has not developed

• Rear tires will not cause lead.

Balancing Wheels Description

S4RS0A2401007

There are two types of wheel and tire balance: static and 
dynamic. Static balance, as shown in figure, is the equal 
distribution of weight around the wheel. Wheels that are 
statically unbalanced cause a bouncing action called 
tramp. This condition will eventually cause uneven tire 
wear.

Dynamic balance, as shown in figure, is the equal 
distribution of weight on each side of the wheel 
centerline so that when the tire spins there is no 
tendency for the assembly to move from side to side. 
Wheels that are dynamically unbalanced may cause 
shimmy.

Inflate tires to recommended pressure

Road test vehicle on level unrouned road in both directions

Switch front tires side to side and road test again

Lead corrected,

if roughness results, replace tires

Leads in same direction

Leads reverses direction

Put tires back in original position 
and check alignment

Install a known-good tire on one front side

Lead remains install a known-good
tire in place of other front tire

Lead remains known-good tires are not good

Lead corrected replace tire

Lead corrected replace tire

I2RH01240007-

1. Heavy spot wheel tramp

[A]: Before correction

2. Balance weights addition point

[B]: Corrective weights

3. C/L of spindle

1. Heavy spot wheel shimmy

[C]: Before correction

2. Balance weights addition point

[D]: Corrective weights

3. C/L of spindle

I2RH01240008-

I2RH01240009-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Bimmer Jakes FRONT HEADLIGHT LENS COVER Replacement Manual preview
FRONT HEADLIGHT LENS COVER
Бренд: Bimmer Jakes Страницы: 4
JANE be cool boosty Manual preview
be cool boosty
Бренд: JANE Страницы: 21
Warrior Products 4560 Manual preview
4560
Бренд: Warrior Products Страницы: 4
PullRite 20K OE Series Installation Instructions Manual preview
20K OE Series
Бренд: PullRite Страницы: 10
BendPak Autostacker PL-6SR Installation And Operation Manual preview
Autostacker PL-6SR
Бренд: BendPak Страницы: 104
U.S. General 95904 Operating Instructions preview
95904
Бренд: U.S. General Страницы: 4
UAZ UAZ-374195 Operating Manual preview
UAZ-374195
Бренд: UAZ Страницы: 90
JANE StrataPlatform Instructions Manual preview
StrataPlatform
Бренд: JANE Страницы: 58
Whispbar K951W Fitting Instructions For Basic Carrier preview
K951W
Бренд: Whispbar Страницы: 15
Kuda 079020 Installation Instruction preview
079020
Бренд: Kuda Страницы: 2
GMC 2013 GMC Savana Owner'S Manual preview
2013 GMC Savana
Бренд: GMC Страницы: 398
Over Armour Offroad TX-STAMP-4-FC04 Instructions For Installation And Care preview
TX-STAMP-4-FC04
Бренд: Over Armour Offroad Страницы: 9
Oldsmobile 2003 Alero Owner'S Manual preview
2003 Alero
Бренд: Oldsmobile Страницы: 354
Cadillac GMC Yukon Denali 2005 Owner'S Manual preview
GMC Yukon Denali 2005
Бренд: Cadillac Страницы: 456
Saab 900 5 Speed Technical Training Manual preview
900 5 Speed
Бренд: Saab Страницы: 63
R&G LP0291BK Fitting Instructions Manual preview
LP0291BK
Бренд: R&G Страницы: 20
Whispbar S17W Fitting Instructions Manual preview
S17W
Бренд: Whispbar Страницы: 70
Kia OPTIA hybrid 2020 Features & Functions Manual preview
OPTIA hybrid 2020
Бренд: Kia Страницы: 54

Бренды по названию

Популярные бренды

Загрузить еще бренды