manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Engine General Information and Diagnosis:  1A-77

DTC Troubleshooting

NOTE:

• Before performed trouble shooting, be sure to read the “Precautions of ECM Circuit Inspection: ”.
• When measuring circuit voltage, resistance and/or pulse signal at ECM connector, connect the 

special tool to ECM and/or the ECM connectors referring to “Inspection of ECM and Its Circuits: ”.

• Upon completion of inspection and repair work, perform “DTC Confirmation Procedure” and 

confirm that the trouble has been corrected.

 

Step

Action

Yes

No

1

Was “Engine and Emission Control System Check” 
performed?

Go to Step 2.

Go to “Engine and 
Emission Control 
System Check: ”.

2

ECT sensor and its circuit check

1) Connect scan tool with ignition switch turned OFF.
2) Turn ON ignition switch.
3) Check engine coolant temp. displayed on scan tool.

Is 119 

q

C (246 

q

F) indicated?

Go to Step 3.

Intermittent trouble.
Check for intermittent 
referring to “Intermittent 
and Poor Connection 
Inspection:  in Section 
00”.

3

ECM voltage check

1) Disconnect connector from ECT sensor with ignition 

switch turned OFF.

2) Check for proper connection to ECT sensor at “LT GRN” 

and “ORN” wire terminals.

3) If OK, then turn ON ignition switch, measure voltage 

between “LT GRN” wire terminal of ECT sensor 
connector and vehicle body ground.

Is voltage about 4 – 6 V?

Go to Step 6.

Go to Step 4.

4

ECT sensor short circuit check

1) Disconnect connectors from ECM with ignition switch 

turned OFF.

2) Measure resistance between “LT GRN” wire terminal of 

ECT sensor connector and vehicle body ground.

Is resistance infinity?

Go to Step 5.

“LT GRN” wire is 
shorted to ground 
circuit.
If wire is OK, substitute 
a known-good ECM and 
recheck.

5

ECT sensor short circuit check

1) Turn ON ignition switch.
2) Measure voltage between “LT GRN” wire terminal of 

ECT sensor connector and vehicle body ground.

Is voltage about 0 V?

Go to Step 6.

“LT GRN” wire is 
shorted to other circuit.
If wire is OK, substitute 
a known-good ECM and 
recheck.

6

ECT sensor for performance check

1) Check ECT sensor according to “Engine Coolant 

Temperature (ECT) Sensor Inspection:  in Section 1C”.

Is it in good condition?

Substitute a known-
good ECM and recheck.

Replace ECT sensor.

I4RS0A110026-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

PUTCO MOLLE PANELS RAM 2500 Instruction Manual preview
MOLLE PANELS RAM 2500
Бренд: PUTCO Страницы: 4
Westfalia Portilo 350000 Installation And Operating Instructions Manual preview
Portilo 350000
Бренд: Westfalia Страницы: 18
PullRite 20K OE Series Installation Instructions Manual preview
20K OE Series
Бренд: PullRite Страницы: 10
Doug Thorley Headers THY-464-1 Instructions preview
THY-464-1
Бренд: Doug Thorley Headers Страницы: 5
Edelbrock 66002 Installation Instructions preview
66002
Бренд: Edelbrock Страницы: 2
Safe Fleet PRIME DESIGN VRR-E-PM21 Assembly Instructions Manual preview
PRIME DESIGN VRR-E-PM21
Бренд: Safe Fleet Страницы: 12
A-Tach 50092 Quick Start Manual preview
50092
Бренд: A-Tach Страницы: 2
Hudson 1933 Eight Owner'S Manual preview
1933 Eight
Бренд: Hudson Страницы: 34
Subaru 1994 Impreza Supplemental Service Manual preview
1994 Impreza
Бренд: Subaru Страницы: 540
Dometic LMC Eriba Nova Service Manual preview
LMC Eriba Nova
Бренд: Dometic Страницы: 24
Ford F-250 Super Duty 2022 Owner'S Manual preview
F-250 Super Duty 2022
Бренд: Ford Страницы: 740
Cadillac 2000 DeVille Service Manual Addendum preview
2000 DeVille
Бренд: Cadillac Страницы: 19
iQOS CCU01 Safety Warnings And Instructions preview
CCU01
Бренд: iQOS Страницы: 4
Porsche 92854 Owner'S Manual preview
92854
Бренд: Porsche Страницы: 145
Metra Electronics 99-6510 User Manual preview
99-6510
Бренд: Metra Electronics Страницы: 17
G-Tech Pro Competition User Manual preview
Pro Competition
Бренд: G-Tech Страницы: 180
National Cycle Quantum Wash'n'Wipe N30205 Assembly Instructions And Owner'S Manual preview
Quantum Wash'n'Wipe N30205
Бренд: National Cycle Страницы: 12
Datsun Saloon I300 Workshop Manual preview
Saloon I300
Бренд: Datsun Страницы: 104

Бренды по названию

Популярные бренды

Загрузить еще бренды