manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Seat Belts:  8A-4

5) Remove front seat belts from the vehicle.

Installation

Install in reverse order of removal, noting the following.
• Seat belt anchor bolts should have an unified fine 

thread (7/16-20 UNF). Under no circumstances 
should any different sized or metric screw threads be 
used.

• Connect Yellow connector (1) to seat belt 

pretensioner securely.
a. Connect connector.
b. Lock connector with lock slider (2).

• Enable air bag system. Refer to “Enabling Air Bag 

System:  in Section 8B”.

Front Seat Belt Inspection

S4RS0A8106003

WARNING:

• Never attempt to disassemble or repair the 

seat belt pretensioner (retractor 
assembly). If any abnormality is found, be 
sure to replace it with new one as an 
assembly.

• Be sure to read “Precautions on Service 

and Diagnosis of Seat Belt: ”, before 
starting to work and observe every 
precaution during work. Neglecting them 
may result in personal injury or 
unactivation of the seat belt pretensioner 
when necessary.

• Never measure resistance of pretensioner 

or disassemble it. Otherwise, personal 
injury may result.

 

CAUTION:

If seat belt pretensioner (retractor assembly) 
was dropped from a height of 30 cm (1 ft) or 
more, it should be replaced.

 

Seat belts and attaching parts can affect the vital 
components and systems of a vehicle.
Therefore, they should be inspected carefully and 
replaced with genuine parts only.

a

b

2

1

3

I2RH01810003-

1

1

2

b)

a)

I5RH01810002-

I2RH01810004-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Qube AP1 Supplemental Instructions preview
AP1
Бренд: Qube Страницы: 19
Cadillac 2000 Warranty And Owner Assistance Information preview
2000
Бренд: Cadillac Страницы: 32
Carax HUD CRX-3001 Quick Start Manual preview
HUD CRX-3001
Бренд: Carax Страницы: 2
Monacor CARPOWER CAP-12XHQ Manual preview
CARPOWER CAP-12XHQ
Бренд: Monacor Страницы: 5
Jeep Grand Cherokee WK2 Owner'S Manual preview
Grand Cherokee WK2
Бренд: Jeep Страницы: 338
Saab 32 025 888 Installation Instructions preview
32 025 888
Бренд: Saab Страницы: 3
GMC Envoy XUV 2004 Getting To Know Manual preview
Envoy XUV 2004
Бренд: GMC Страницы: 20
Ford 2004 Navigator Owner'S Manual preview
2004 Navigator
Бренд: Ford Страницы: 368
iOttie Aivo Connect Setup Manual preview
Aivo Connect
Бренд: iOttie Страницы: 58
Pet Gear TRI-FOLD PG9300RF Instruction Manual preview
TRI-FOLD PG9300RF
Бренд: Pet Gear Страницы: 4
Hyundai Entourage 2008 Quick Reference Manual preview
Entourage 2008
Бренд: Hyundai Страницы: 11
Camoplast T4S Installation Manuallines preview
T4S
Бренд: Camoplast Страницы: 19
travall TDG 1486 Fitting Instructions preview
TDG 1486
Бренд: travall Страницы: 4
Quadratec QuadraTop 11051.0415 Installation Manual preview
QuadraTop 11051.0415
Бренд: Quadratec Страницы: 8
Packard 1948 eight Operating Instructions Manual preview
1948 eight
Бренд: Packard Страницы: 25
Metra Electronics 99-5026 Installation Instructions Manual preview
99-5026
Бренд: Metra Electronics Страницы: 20
Mazda 3 Facelift 2006 Training Manual preview
3 Facelift 2006
Бренд: Mazda Страницы: 94
Thule 145012 Quick Start Manual preview
145012
Бренд: Thule Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды