manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Air Bag System:  8B-125

21) Wash your hands with mild soap and water 

afterward.

NOTE:
Remaining steps are to be followed in the 
unlikely event that air bag (inflator) module 
did not deploy or seat belt pretensioner did 
not activate.

 

22) Ensure that deployment harness has been 

disconnected from 12 volts vehicle battery and that 
its two banana plugs have been shorted together by 
fully seating one banana plug into the other.

23) Disconnect deployment harness and adapter cable 

from air bag (inflator) module or seat belt 
pretensioner.

24) Temporarily store undeployed air bag (inflator) 

module referring to “Precautions on Service and 
Diagnosis of Air Bag System: ” for details.

25) Contact your local distributor for further assistance.

Deployment / Activation Inside of Vehicle

When the vehicle will be destroyed, or salvaged for 
component parts, deploy the air bag modules and/or 
activate seat belt pretensioners installed on vehicle.

NOTE:
If equipped with the seat belt pretensioners, 
activate both side of seat belt pretensioners 
at the same time when using special tool (C).

 

1) Turn ignition switch to LOCK position, remove key 

and put on safety glasses.

2) Remove all loose objects from front seats and 

instrument panel.

3) Disconnect air bag (inflator) module or seat belt 

pretensioner connector as follows.
• For driver and passenger air bag (inflator) module 

[A]
Remove glove box from instrument panel and 
disconnect driver and passenger air bag (inflator) 
module connector (1).

• For side-air bag (inflator) module [B]

Disconnect side-air bag (inflator) module 
connectors (2) under front seat cushion.

• For side curtain-air bag (inflator) module [C]

Remove rear pillar trim and disconnect side 
curtain-air bag (inflator) module connectors (3).

• For seat belt pretensioners (right and left) [D]

Remove both side (driver and passenger side) 
center pillar lower trim and disconnect seat belt 
pretensioner connectors (4).

4) Confirm that each air bag (inflator) module and/or 

seat belt pretensioners is securely mounted.

[A]

[B]

[C]

[D]

2

1

3

4

1

2

1

2

1

2

1

2

I4RS0A820093-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Jacobsen Cushman Turf Truckster Parts & Maintenance Manual preview
Cushman Turf Truckster
Бренд: Jacobsen Страницы: 210
DAVIS 8126GD User Manual preview
8126GD
Бренд: DAVIS Страницы: 32
Dometic GROUP DRS2 Installation And Operating Manual preview
DRS2
Бренд: Dometic GROUP Страницы: 20
Camcar 40108 Mounting Instructions preview
40108
Бренд: Camcar Страницы: 6
ABL eMH3 Quick Start Manual preview
eMH3
Бренд: ABL Страницы: 4
Honda Pilot 2019 Owner'S Manual preview
Pilot 2019
Бренд: Honda Страницы: 85
Van Guard VG273 Fitting Instructions preview
VG273
Бренд: Van Guard Страницы: 3
Dakota Digital LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne... Installation Instructions preview
LED Tail Lights for 1959 Chevrolet Impala, Bel Air, Biscayne...
Бренд: Dakota Digital Страницы: 3
Sears 580.32601 Owner'S Manual preview
580.32601
Бренд: Sears Страницы: 41
Lit Lightz RGBW Rock Lights Setup Manual preview
RGBW Rock Lights
Бренд: Lit Lightz Страницы: 3
CTEK D250S Dual Manual preview
D250S Dual
Бренд: CTEK Страницы: 84
Westfalia 305 158 Mounting Instructions preview
305 158
Бренд: Westfalia Страницы: 10
Ecco 13 Series Installation And Operation Instructions Manual preview
13 Series
Бренд: Ecco Страницы: 24
Paccar PACCHARGE AC20 Installation Manual preview
PACCHARGE AC20
Бренд: Paccar Страницы: 63
AutoLoc SB3PR Series User Manual And Installation Manual preview
SB3PR Series
Бренд: AutoLoc Страницы: 6
Yakima Landing Pad 11 Manual preview
Landing Pad 11
Бренд: Yakima Страницы: 28
Kuda 076100 Installation Instruction preview
076100
Бренд: Kuda Страницы: 3
Axxess AXGMLN-09 Installation Instructions preview
AXGMLN-09
Бренд: Axxess Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды