manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

1D-15 Engine Mechanical: 

Intake Manifold Removal and Installation

S4RS0A1406010

Removal

1) Remove throttle body referring to “Throttle Body 

Removal and Installation: ”.

2) Disconnect MAP sensor coupler (1).
3) Disconnect the following hoses:

• Brake booster hose (2) from cylinder head cover
• PCV hose (3) from PCV valve

4) Remove EGR pipe bolt (4) from EGR valve.

5) Remove intake manifold (1) and EGR pipe (2) from 

cylinder head, and then remove its gasket and O-
ring.

Installation

Reverse removal procedure for installation noting the 
followings.
• Use new intake manifold O-ring.
• Use new EGR pipe gasket and O-ring.
• Tighten EVAP canister purge valve bracket bolt to 

specified torque.

Tightening torque
EVAP canister purge valve bracket bolt:  5 N·m (
0.5 kg-m, 4.0 lb-ft)

• Install intake manifold bolt (2) and nut (1) as shown in 

figure.

• Check to ensure that all removed parts are back in 

place.
Reinstall any necessary parts which have not been 
reinstalled.

• Adjust accelerator cable play, referring to “Accelerator 

Cable Adjustment: ”.

• Refill cooling system referring to “Cooling System 

Flush and Refill:  in Section 1F”.

• Upon completion of installation, turn ignition switch 

ON but engine OFF and check for fuel leaks.

• Finally, start engine and check for engine coolant 

leaks.

3

1

2

4

I4RS0A140004-

1

2

I3RM0A140018-

1

2

2

I4RS0A140005-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Garmin BC 30 Owner'S Manual preview
BC 30
Бренд: Garmin Страницы: 2
Federal Signal Corporation CommCenter D1 Series Installation And Service Instructions Manual preview
CommCenter D1 Series
Бренд: Federal Signal Corporation Страницы: 16
JANE be cool boosty Manual preview
be cool boosty
Бренд: JANE Страницы: 21
Genesis Multiple G9F18 AU000 Quick Start Manual preview
Multiple G9F18 AU000
Бренд: Genesis Страницы: 3
Buick 2005 Terraza Owner'S Manual preview
2005 Terraza
Бренд: Buick Страницы: 428
Actia TGU-R ACCESS User Manual preview
TGU-R ACCESS
Бренд: Actia Страницы: 37
Chrysler Stratus LHD 1997 Interactive Electronic Service Manual preview
Stratus LHD 1997
Бренд: Chrysler Страницы: 1534
Demco TP20047 Assembly Operation Replacement Parts preview
TP20047
Бренд: Demco Страницы: 4
Dodge 2010 Challenger SRT Owner'S Manual preview
2010 Challenger SRT
Бренд: Dodge Страницы: 444
Volvo 1989 780 Owner'S Manual preview
1989 780
Бренд: Volvo Страницы: 123
SIXTOL DRY CAR Instructions For Use Manual preview
DRY CAR
Бренд: SIXTOL Страницы: 32
Subaru 1999 Legacy Owner'S Manual preview
1999 Legacy
Бренд: Subaru Страницы: 399
Van Guard VG162S Fitting Instructions preview
VG162S
Бренд: Van Guard Страницы: 3
RAM Truck 2500 2018 Supplement Manual preview
Truck 2500 2018
Бренд: RAM Страницы: 32
Chevrolet 2012 Malibu Owner'S Manual preview
2012 Malibu
Бренд: Chevrolet Страницы: 376
BMW X1 2015 Owner'S Manual preview
X1 2015
Бренд: BMW Страницы: 242
Toyota Sienna 2000 Operating Manual preview
Sienna 2000
Бренд: Toyota Страницы: 277
E&P HYDRAULICS Electronic Levelling System User Manual preview
Electronic Levelling System
Бренд: E&P HYDRAULICS Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды