manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

5A-148 Automatic Transmission: 

4) Apply grease to oil seal lip.

:  Grease 99000–25030

Automatic Transaxle Unit Inspection and 
Adjustment

S4RS0A5106063

Inspection

Brake discs

Dry and inspect them for pitting, burn flaking, significant 
wear, glazing, cracking, charring and chips or metal 
particles imbedded in lining.
If discs show any of the above conditions, replacement 
is required.

NOTE:

• If disc lining is exfoliated or discolored, 

replace all discs.

• Before assembling new discs, soak them 

in A/T fluid for at least two hours.

 

Brake separator plates and retaining plates

Dry plates and check for discoloration. If plate surface is 
smooth and even color smear is indicated, plate should 
be reused. If severe heat spot discoloration or surface 
scuffing is indicated, plate must be replaced.

Brake return spring subassembly

Measure brake return springs.
Evidence of extreme heat or burning in the area of clutch 
may have caused springs to take heat set and would 
require their replacement.

Free length of 1st & reverse brake return spring
“a”: 21.71 mm (0.855 in.)

Free length of 2nd brake return spring
“a”: 15.85 mm (0.624 in.)

NOTE:

• Do not apply excessive force when 

measuring spring free length.

• Perform measurement at several points.

 

One-way clutch No.1 assembly

1) Install one-way clutch No.1 assembly (2) to rear 

planetary sun gear subassembly (1).

2) Securing rear planetary sun gear subassembly, 

ensure that one-way clutch No.1 assembly rotates 
only in one direction.
If the one-way clutch rotates in both directions or it 
does not rotate in either direction, replace it with new 
one.

I2RH0B510252-

I2RH01510147-

I2RH0B510253-

I2RH0B510173-

I2RH0B510254-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Garmin BC 30 Owner'S Manual preview
BC 30
Бренд: Garmin Страницы: 2
Tesla V2 SUPERCHARGER First Responder'S Manual preview
V2 SUPERCHARGER
Бренд: Tesla Страницы: 9
GATmatic TWC-562S Installation, Operation & Maintenance Manual preview
TWC-562S
Бренд: GATmatic Страницы: 13
FAAFTECH FT-VF-HND2 Installation Manual preview
FT-VF-HND2
Бренд: FAAFTECH Страницы: 8
AutoMaxi AXIS XXL Instructions preview
AXIS XXL
Бренд: AutoMaxi Страницы: 2
Rago FABRICATION R2223TTUNDM Installation Manual preview
R2223TTUNDM
Бренд: Rago FABRICATION Страницы: 10
Menabo JUZA Fitting Instructions Manual preview
JUZA
Бренд: Menabo Страницы: 12
tams elektronik 54-01016 Manual preview
54-01016
Бренд: tams elektronik Страницы: 44
Whelen Engineering Company FastTrax FTF4 Installation Manual preview
FastTrax FTF4
Бренд: Whelen Engineering Company Страницы: 9
ULTIMATE SPEED 279746 Assembly And Safety Advice preview
279746
Бренд: ULTIMATE SPEED Страницы: 6
OHIOSTEEL 1084TR Quick Start Manual preview
1084TR
Бренд: OHIOSTEEL Страницы: 2
Blaupunkt 7 608 502 000 Installation Instructions Manual preview
7 608 502 000
Бренд: Blaupunkt Страницы: 6
Mitsubishi Outlander Plug-in hybrid Quick Manual preview
Outlander Plug-in hybrid
Бренд: Mitsubishi Страницы: 28
Axxess AXGMLN-09 Installation Instructions preview
AXGMLN-09
Бренд: Axxess Страницы: 4
Kargo Master 80070 Instruction Manual preview
80070
Бренд: Kargo Master Страницы: 17
Tuff Tonneaus Bunji Ute Installation Instructions preview
Bunji Ute
Бренд: Tuff Tonneaus Страницы: 4
Cadillac 1967 Calais Coupe Data Book preview
1967 Calais Coupe
Бренд: Cadillac Страницы: 255
Snapper 63151 Parts Manual preview
63151
Бренд: Snapper Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды