manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

4C-5 Rear Brakes: 

5) Remove push nut (1).
6) Remove parking brake shoe lever (2) from shoe rim 

(3).

Installation

Install parts in reverse order of removal, noting the 
following.
• Install shoe hold down springs (1) by pushing them 

down in place and turning hold down pins (2).

• Install brake drum referring to step 2) to 10) of “Rear 

Brake Drum Removal and Installation: ”.

Rear Brake Shoe Inspection

S4RS0A4306005

• Check ratchet of brake strut (1) assembly for wear or 

damage.

• Check shoe return spring, antirattle spring and shoe 

hold down spring for damage, corrosion and 
weakening.

• Check for smooth movement of brake shoe lever (2) 

along shoe rim.

If any defective or malfunction is found, repair or replace.

Wheel Cylinder Removal and Installation

S4RS0A4306006

Removal

1) Remove brake drum referring to “Rear Brake Drum 

Removal and Installation: ”.

2) Remove brake shoe referring to “Rear Brake Shoe 

Removal and Installation: ”.

3) Loosen brake pipe flare nut (1) but only within the 

extent that fluid does not leak.

4) Remove wheel cylinder mounting bolts. Disconnect 

brake pipe from wheel cylinder and put bleeder plug 
cap (1) onto pipe to prevent fluid from spilling.

Installation

1) Take off bleeder plug cap from brake pipe and 

connect pipe to wheel cylinder (1) just enough to 
prevent fluid from leaking.

2) Install wheel cylinder (1) to brake back plate (2), and 

tighten wheel cylinder mounting bolts to specified 
torque.

Tightening torque
Wheel cylinder mounting bolt (a):  12 N·m (1.2 
kg-m, 9.0 lb-ft)

3) Tighten flare nut of brake pipe (3) to specified torque.

Tightening torque
Rear brake pipe flare nut (b):  16 N·m (1.6 kg-m, 
11.5 lb-ft)

1

2

3

I4RS0A430014-

2

1

I4RS0A430012-

I4RS0A430016-

1

I4RS0A430015-

1

I4RS0A430017-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Wagan Road Ready Seat Protector User Manual preview
Road Ready Seat Protector
Бренд: Wagan Страницы: 12
Chevrolet 2016 Suburban Owner'S Manual preview
2016 Suburban
Бренд: Chevrolet Страницы: 50
EUFAB 16465 Operating Instructions Manual preview
16465
Бренд: EUFAB Страницы: 12
Prorack K374 Manual preview
K374
Бренд: Prorack Страницы: 14
Whispbar K481W Fitting Instructions Manual preview
K481W
Бренд: Whispbar Страницы: 14
Honda 2000 Accord Sedan Online Reference Owner'S Manual preview
2000 Accord Sedan
Бренд: Honda Страницы: 320
ZENEC ZE-RVC85WA Mounting Instructions preview
ZE-RVC85WA
Бренд: ZENEC Страницы: 2
Prorack K443 Fitting Instructions Manual preview
K443
Бренд: Prorack Страницы: 14
Saab 9-3 M03- Installation Instructions Manual preview
9-3 M03-
Бренд: Saab Страницы: 16
Teletrac Prism TM450 Installation Manual preview
Prism TM450
Бренд: Teletrac Страницы: 12
Prorack K146 Fitting Instructions Manual preview
K146
Бренд: Prorack Страницы: 14
Honda 2011 ODYSSEY TOURING Technology Reference Manual preview
2011 ODYSSEY TOURING
Бренд: Honda Страницы: 21
Myria MY2118 User Manual preview
MY2118
Бренд: Myria Страницы: 16
Thule 1170 Instructions Manual preview
1170
Бренд: Thule Страницы: 8
Thule XT Kit 3144 Instructions Manual preview
XT Kit 3144
Бренд: Thule Страницы: 8
Thule TracRac SR Manual preview
TracRac SR
Бренд: Thule Страницы: 16
Thule Slide Out G2 12V Crafter 2017 Installation Instructions Manual preview
Slide Out G2 12V Crafter 2017
Бренд: Thule Страницы: 20
Thule Rapid System 1392 Fitting Instructions Manual preview
Rapid System 1392
Бренд: Thule Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды