manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Automatic Transmission:  5A-99

“3” Position Switch Inspection

S4RS0A5106014

1) Remove console box referring to “Console Box 

Components:  in Section 9H”.

2) Disconnect “3” position switch connector (1).
3) Check continuity between “3” position switch 

terminals.

“3” position switch specification
Shift selector lever to “3” or “2” range: 
Continuity
Shift other above range: No continuity

Solenoid Valves (Shift Solenoid Valves and 
Timing Solenoid Valve) Removal and 
Installation

S4RS0A5106015

Removal

1) Disconnect negative cable at battery.
2) Lift up vehicle.
3) Remove drain plug and drain A/T fluid.
4) Install drain plug.

Tightening torque
A/T fluid drain plug:  17 N·m (1.7 kg-m, 12.5 lb-ft)

5) Remove A/T oil pan (1) and oil pan gasket (2).
6) Remove oil strainer assembly (3).

7) Remove transmission fluid temperature sensor (1) 

from sensor clamp.

8) Disconnect solenoid connectors (2).

9) Remove shift solenoid valve-A (No.1) (1), shift 

solenoid valve-B (No.2) (2) and timing solenoid valve 
(3) by removing bolts.

1

I4RS0A510026-

I2RH0B510054-

1

2

I4RS0A510027-

1

2

3

I4RS0A510028-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Vaisala MD30 Setup Manual preview
MD30
Бренд: Vaisala Страницы: 24
RAM CHASSIS CAB 3500 2017 Quick Reference Manual preview
CHASSIS CAB 3500 2017
Бренд: RAM Страницы: 16
iRacing Porsche 911 GT3 R User Manual preview
Porsche 911 GT3 R
Бренд: iRacing Страницы: 25
Würth 071554055 User Instructions preview
071554055
Бренд: Würth Страницы: 36
Quadratec 12057.0261 Installation Manual preview
12057.0261
Бренд: Quadratec Страницы: 12
Whispbar K919W Fitting Instructions Manual preview
K919W
Бренд: Whispbar Страницы: 17
cam PFF Series Operating Manual preview
PFF Series
Бренд: cam Страницы: 28
Mitsubishi MOTORS PAJERO SPORT Manual preview
PAJERO SPORT
Бренд: Mitsubishi MOTORS Страницы: 416
Waeco MagicSpeed MS900 Installation Manual preview
MagicSpeed MS900
Бренд: Waeco Страницы: 120
Ranger design 1525-PCX Installation Manual preview
1525-PCX
Бренд: Ranger design Страницы: 22
FIRRAK FIRRAK arca Assembly Instructions Manual preview
FIRRAK arca
Бренд: FIRRAK Страницы: 12
Quadratec 506-Rock Quick Start Quide preview
506-Rock
Бренд: Quadratec Страницы: 2
Directed 933.SUBARU1 Installation Manual preview
933.SUBARU1
Бренд: Directed Страницы: 24
AMP Research BEDXTENDER HD 74805-00A Assembly And Installation Manual preview
BEDXTENDER HD 74805-00A
Бренд: AMP Research Страницы: 7
NanoCam Plus NANO CONNECT Smartview 72 Quick Start Manual preview
NANO CONNECT Smartview 72
Бренд: NanoCam Plus Страницы: 4
Fab Fours Z1550 Installation Manual preview
Z1550
Бренд: Fab Fours Страницы: 18
Van Guard IN8377 Fitting Instructions Manual preview
IN8377
Бренд: Van Guard Страницы: 12
Volvo V60 Owner'S Manual preview
V60
Бренд: Volvo Страницы: 176

Бренды по названию

Популярные бренды

Загрузить еще бренды