manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Engine General Information and Diagnosis:  1A-31

9

Check fuel pump for operation

Was fuel pump operating sound heard from fuel filler for 
about 3 seconds after ignition switch ON and stop?

Go to “Fuel Pressure 
Check: ”.

Go to “Fuel Pump and 
Its Circuit Check: ”.

10

Check ignition spark

1) Disconnect injector couplers.
2) Remove spark plugs and connect them to high-tension 

cords or ignition coil assembly.

3) Ground spark plugs.
4) Crank engine and check if each spark plug sparks.

Is it in good condition?

Go to Step 11.

Go to “Ignition Spark 
Test:  in Section 1H”.

11

Check fuel injector for operation

1) Install spark plugs and connect injector connectors.
2) Using sound scope (1), check operating sound of each 

injector (2) when cranking engine.

Was injector operating sound heard from all injectors?

Go to “Engine Symptom 
Diagnosis: ”.

Go to “Fuel Injector 
Circuit Check: ”.

Step

Action

Yes

No

I3RM0A110015-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Thule 1306 RAPID SYSTEM Fitting Instructions Manual preview
1306 RAPID SYSTEM
Бренд: Thule Страницы: 8
Axxess AXGMLN-08 Installation Instructions Manual preview
AXGMLN-08
Бренд: Axxess Страницы: 8
Ford Focus ST 2018 Supplement Manual preview
Focus ST 2018
Бренд: Ford Страницы: 38
Whispbar K728W Fitting Instructions Manual preview
K728W
Бренд: Whispbar Страницы: 85
PAC GM1A-R Quick Start Manual preview
GM1A-R
Бренд: PAC Страницы: 4
Honda Sedan CIVIC 2022 Manual preview
Sedan CIVIC 2022
Бренд: Honda Страницы: 701
v.link VL2-MBN2 Manual preview
VL2-MBN2
Бренд: v.link Страницы: 12
Honda 08V31-TE0-100A Installation Instructions Manual preview
08V31-TE0-100A
Бренд: Honda Страницы: 10
Hella 2DA 008 136-031 Mounting Instructions preview
2DA 008 136-031
Бренд: Hella Страницы: 2
Safe Fleet Prime Design OCM-3032 Quick Start Manual preview
Prime Design OCM-3032
Бренд: Safe Fleet Страницы: 4
Porsche BOXTER - Technical Manual preview
BOXTER -
Бренд: Porsche Страницы: 146
Blue Ox BX1120 Installation Instructions preview
BX1120
Бренд: Blue Ox Страницы: 5
Buick 1995 Roadmaster Manual preview
1995 Roadmaster
Бренд: Buick Страницы: 340
Istar PI00670 Instruction Manual preview
PI00670
Бренд: Istar Страницы: 6
Proxel EPS-DUAL Installation Instructions & User Manual preview
EPS-DUAL
Бренд: Proxel Страницы: 16
Aries 2157002 Installation Manual preview
2157002
Бренд: Aries Страницы: 6
Igloo IE24 Operating Instructions Manual preview
IE24
Бренд: Igloo Страницы: 76
Toyota GR Supra 2021 Quick Reference Manual preview
GR Supra 2021
Бренд: Toyota Страницы: 48

Бренды по названию

Популярные бренды

Загрузить еще бренды