manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

5A-102 Automatic Transmission: 

Pressure Control Solenoid Valves (Pressure 
Control Solenoid and TCC Pressure Control 
Solenoid) Removal and Installation

S4RS0A5106060

Removal

1) Disconnect negative cable at battery.
2) Lift up vehicle.
3) Remove drain plug and drain A/T fluid.
4) Install drain plug.

Tightening torque
A/T fluid drain plug:  17 N·m (1.7 kg-m, 12.5 lb-ft)

5) Remove A/T oil pan (1) and oil pan gasket (2).
6) Remove oil strainer assembly (3).

7) Remove transmission fluid temperature sensor (1) 

from sensor clamp.

8) Disconnect solenoid connectors (2).

9) Remove valve body assembly referring to 

“Automatic Transaxle Unit Disassembly: ”.

10) Remove pressure control solenoid valve and TCC 

pressure control solenoid valve referring to “Valve 
Body Assembly Disassembly and Reassembly: ”.

Installation

Reverse removal procedure to install pressure control 
solenoid valve and valve body assembly noting the 
following points.
• For detail of pressure control solenoid valve and TCC 

pressure control solenoid valve installation, refer to 
“Valve Body Assembly Disassembly and Reassembly: 
”.

• For detail of valve body assembly installation, refer to 

“Automatic Transaxle Unit Assembly: ”.

• For detail of installing wire harness for solenoid valves 

and sensor, refer to “Automatic Transaxle Unit 
Assembly: ”. Use new O-rings.

• For detail of A/T oil pan and oil strainer assembly 

installation, refer to “Automatic Transaxle Unit 
Assembly: ”. Use new oil pan gasket.

• Pour A/T fluid and check fluid level according to 

procedure described in “A/T Fluid Change: ”.

• Check for fluid leakage after warming up A/T.

Pressure Control Solenoid Valve Inspection

S4RS0A5106017

CAUTION:

• Be very careful as dust etc. does enter 

when pressure control solenoid valves are 
inspected.

 

Resistance Check

Measure resistance between pressure control solenoid 
valves (Pressure control solenoid and TCC pressure 
control solenoid) (1) terminals.

Pressure control solenoid valve and TCC pressure 
control solenoid valve resistance
Standard: 5.0 – 5.6 

:

 at 20 

q

C (68 

q

F)

Operation Check

Check pressure control solenoid valves (Pressure 
control solenoid and TCC pressure control solenoid) 
operation in the either manner of the following.

I2RH0B510054-

1

2

I4RS0A510027-

1

I2RH01510071-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

UnderCover 2110 Installation Manual preview
2110
Бренд: UnderCover Страницы: 16
Yakima K618 Instructions Manual preview
K618
Бренд: Yakima Страницы: 11
RAM 2015 1500 User Manual preview
2015 1500
Бренд: RAM Страницы: 292
RAM Trucks 1500 User Manual preview
Trucks 1500
Бренд: RAM Страницы: 116
Quadratec QuadraTop Adventure Top S Installation Manual preview
QuadraTop Adventure Top S
Бренд: Quadratec Страницы: 20
Kia 2011 optima Owner'S Manual preview
2011 optima
Бренд: Kia Страницы: 385
Mercedes-Benz 2013 C-Class Coupe Owner'S Manual preview
2013 C-Class Coupe
Бренд: Mercedes-Benz Страницы: 388
Standby L54 Manual preview
L54
Бренд: Standby Страницы: 10
Mobile Create MCM3 Instruction Manual preview
MCM3
Бренд: Mobile Create Страницы: 15
Vintage Air 561163 Manual preview
561163
Бренд: Vintage Air Страницы: 28
Motoalliance VIPER MA11922 Install Instructions Manual preview
VIPER MA11922
Бренд: Motoalliance Страницы: 8
Jeep 2014 Grand Cherokee SRT8 Owner'S Manual preview
2014 Grand Cherokee SRT8
Бренд: Jeep Страницы: 596
Skoda 1K0 051 437 Assembly Instructions preview
1K0 051 437
Бренд: Skoda Страницы: 4
Whelen Engineering Company FastTrax FTF4 Installation Manual preview
FastTrax FTF4
Бренд: Whelen Engineering Company Страницы: 9
Metra Electronics 99-7860 Installation Instructions preview
99-7860
Бренд: Metra Electronics Страницы: 5
Renkforce RF-4743771 Operating Instructions preview
RF-4743771
Бренд: Renkforce Страницы: 4
H&S XRT Pro Installation & Operation Manual preview
XRT Pro
Бренд: H&S Страницы: 32
Black+Decker BXAE00011 Operating Instructions Manual preview
BXAE00011
Бренд: Black+Decker Страницы: 21

Бренды по названию

Популярные бренды

Загрузить еще бренды