manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Automatic Transmission:  5A-141

Valve Body Assembly Disassembly and 
Reassembly

S4RS0A5106051

CAUTION:

When replacing pressure control solenoid 
valve and/or TCC pressure control solenoid 
valve, it is strictly required to replace it 
together with valve body assembly as a set. 
Replacing pressure control solenoid valve 
and/or TCC pressure control solenoid valve 
independently may cause excessive shift 
shock.

 

Disassembly

1) Pull out manual valve (1).

2) Remove pressure control solenoid valve (1).

3) Remove TCC pressure control solenoid valve (1).

4) Remove shift solenoid valve-A (1).

5) Remove shift solenoid valve-B (1).

6) Remove timing solenoid valve (1).

7) Remove temperature sensor clamp (1).

2. Solenoid lock plate

I2RH0B510216-

I2RH0B510217-

1

I4RS0A510045-

I2RH0B510219-

I2RH0B510220-

I2RH0B510221-

I2RH0B510222-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Samsung HF1000 User Manual preview
HF1000
Бренд: Samsung Страницы: 133
Quadratec QuadraTop Adventure Top S Installation Manual preview
QuadraTop Adventure Top S
Бренд: Quadratec Страницы: 20
Alpine eX-10 Owner'S Manual preview
eX-10
Бренд: Alpine Страницы: 69
Allen Sports S302 Instructions preview
S302
Бренд: Allen Sports Страницы: 2
ULTIMATE SPEED 94600 Assembly And Safety Advice preview
94600
Бренд: ULTIMATE SPEED Страницы: 21
Skoda KAROQ 2017 Owner'S Manual preview
KAROQ 2017
Бренд: Skoda Страницы: 324
Alphasonik PCP15LDE Owner'S Manual preview
PCP15LDE
Бренд: Alphasonik Страницы: 8
Whelen Engineering Company LED Dominator TAM83S2 Installation Manual preview
LED Dominator TAM83S2
Бренд: Whelen Engineering Company Страницы: 2
Vauxhall 2013 Ampera Infotainment Manual preview
2013 Ampera
Бренд: Vauxhall Страницы: 95
Federal Signal Corporation HighLighter Installation And Programming preview
HighLighter
Бренд: Federal Signal Corporation Страницы: 20
Istar PI00670 Instruction Manual preview
PI00670
Бренд: Istar Страницы: 6
INNO TR163 Installation Instructions preview
TR163
Бренд: INNO Страницы: 3
Kargo Master PRO-IV Assembly Instructions Manual preview
PRO-IV
Бренд: Kargo Master Страницы: 8
Rhino-Rack RBC044 Installation Instructions preview
RBC044
Бренд: Rhino-Rack Страницы: 5
Federal Signal Corporation LEDTCL97 Installation And Service Instructions Manual preview
LEDTCL97
Бренд: Federal Signal Corporation Страницы: 12
MSD Ignition 8381 Installation Instructions preview
8381
Бренд: MSD Ignition Страницы: 4
AAMP Global ECHOMASTER PRO ParkAlert PS-TRUCK30 User Manual preview
ECHOMASTER PRO ParkAlert PS-TRUCK30
Бренд: AAMP Global Страницы: 12
Thule 202 Installation Instructions preview
202
Бренд: Thule Страницы: 1

Бренды по названию

Популярные бренды

Загрузить еще бренды