manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Automatic Transmission:  5A-93

A/T Fluid Change

S4RS0A5106002

CAUTION:

Do not use any fluid other than the specified 
ATF. Use of any fluid other than the specified 
ATF may cause juddering or some other 
faulty condition to occur.

 

1) Lift up vehicle.
2) When engine is cool, remove drain plug (1) from 

transaxle housing (2) and drain A/T fluid.

3) Install drain plug (1).

Tightening torque
A/T fluid drain plug (a):  17 N·m (1.7 kg-m, 12.5 
lb-ft)

4) Lower vehicle and pour proper amount of SUZUKI 

ATF 3317 or Mobil ATF 3309.

5) Check fluid level referring to “A/T Fluid Level Check: 

”.

Automatic transaxle fluid
SUZUKI ATF 3317 or Mobil ATF 3309

Automatic transaxle fluid capacity
When draining from drain plug hole: 3.3 liters 
(6.97 / 5.81 US/Imp. pt.)
When overhauling: 5.6 liters (11.83 / 9.86 US/Imp. 
pt.)

Selector Lever Components

S4RS0A5106004

1. Fluid level gauge

3. “LOW HOT” mark

2. “FULL HOT” mark

I3RM0B510032-

I3RM0B510033-

1. Fluid level gauge

4. “FULL COLD” mark

2. “FULL HOT” mark

5. “LOW COLD” mark

3. “LOW HOT” mark

1. Shift lock solenoid

3. Connector

2. Selector lever assembly

4. “3” position switch

I3RM0B510032-

1

2

3

4

I4RS0A510052-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Eaton Green Motion DC 22 Training preview
Green Motion DC 22
Бренд: Eaton Страницы: 65
Jeep PATRIOT 2013 Specifications preview
PATRIOT 2013
Бренд: Jeep Страницы: 5
Jeep PATRIOT 2012 Specifications preview
PATRIOT 2012
Бренд: Jeep Страницы: 6
Jeep Grand Cherokee SRT 2014 Operating Manual preview
Grand Cherokee SRT 2014
Бренд: Jeep Страницы: 345
Jeep Grand Cherokee 2015 User Manual preview
Grand Cherokee 2015
Бренд: Jeep Страницы: 236
Jeep Grand Cherokee Quick Manual To Repairs preview
Grand Cherokee
Бренд: Jeep Страницы: 18
Jeep Grand Cherokee Quick Reference Manual preview
Grand Cherokee
Бренд: Jeep Страницы: 24
Jeep Compass 2015 Owner'S Manual preview
Compass 2015
Бренд: Jeep Страницы: 560
Jeep Compass 2013 Owner'S Manual preview
Compass 2013
Бренд: Jeep Страницы: 525
Jeep Cherokee 2019 User Manual preview
Cherokee 2019
Бренд: Jeep Страницы: 308
Jeep CHEROKEE 2017 Manual preview
CHEROKEE 2017
Бренд: Jeep Страницы: 86
Jeep CHEROKEE 2017 Owner'S Manual preview
CHEROKEE 2017
Бренд: Jeep Страницы: 638
Jeep 2022 CHEROKEE Quick Start Manual preview
2022 CHEROKEE
Бренд: Jeep Страницы: 9
Jeep 2014 Patriot Service Information preview
2014 Patriot
Бренд: Jeep Страницы: 51
Jeep Jeep Wrangler Buyer'S Manual preview
Jeep Wrangler
Бренд: Jeep Страницы: 4
Jeep Jeep Wrangler Owner'S Manual Supplement preview
Jeep Wrangler
Бренд: Jeep Страницы: 50
Jeep Grand Cherokee SRT 2014 Owner'S Manual preview
Grand Cherokee SRT 2014
Бренд: Jeep Страницы: 118
Jeep 2014 Grand Cherokee Accessories Quick Reference Manual preview
2014 Grand Cherokee
Бренд: Jeep Страницы: 24

Бренды по названию

Популярные бренды

Загрузить еще бренды