Suzuki SWIFT RS415 2017 Скачать руководство пользователя страница 131 | Manualshive

Страница: 131 / 1257

background image

Engine General Information and Diagnosis: 1A-83

5

Wire harness check

1) Turn ignition switch to OFF position.
2) Disconnect connectors from MAP sensor and A/C

refrigerant pressure sensor.

3) Turn ignition switch to ON position.
4) Measure voltage between “GRY/RED” wire terminal of

TP sensor connector and vehicle body ground.

Is terminal voltage about 4 – 6 V?

Faulty MAP sensor and/
or A/C refrigerant
pressure sensor, check
MAP sensor and/or A/C
refrigerant pressure
sensor according to
“Manifold Absolute
Pressure (MAP) Sensor
Inspection: in Section
1C” or “A/C Refrigerant
Pressure Sensor and Its
Circuit Inspection: in
Section 7B”.

Go to Step 6.

6

ECM voltage check

1) Turn ignition switch to OFF position.
2) Remove ECM from its bracket with ECM connectors

connected.

3) Check for proper connection of ECM connector at “C37-

14” terminal.

4) Turn ignition switch to ON position.
5) Measure voltage between “C37-14” terminal of ECM

connector and vehicle body ground.

Is terminal voltage about 4 – 6 V?

“GRY/RED” wire is open
or high resistance
circuit.

Go to Step 8.

7

ECM voltage check

1) Turn ignition switch to OFF position.
2) Check for proper connection of ECM connector at “C37-

54” terminal.

3) Turn ignition switch to ON position.
4) Measure voltage between “C37-54” terminal of ECM

connector and vehicle body ground.

Is terminal voltage about 4 – 6 V?

“GRY/BLU” wire is open
or high resistance
circuit.

Go to Step 8.

8

Wire circuit check

1) Disconnect connectors from ECM with ignition switch

turned OFF.

2) Measure resistance between “GRY/RED” wire terminal

of TP sensor connector and vehicle body ground,
between “GRY/BLU” wire terminal of TP sensor
connector and body ground and between “GRY/BLU”
and “ORN” wire terminals of TP sensor connector.

Is resistance infinity?

Go to Step 9.

“GRY/RED” and/or
“GRY/BLU” wire are
shorted to ground circuit
and /or “GRY/BLU” wire
is shorted to “ORN”
wire.
If wires are OK,
substitute a known-
good ECM and recheck.

9

Wire circuit check

1) Turn ON ignition switch.
2) Measure voltage between “GRY/RED” wire terminal of

ECM connector and vehicle body ground and between
“GRY/BLU” wire terminal of ECM connector and vehicle
body ground.

Is voltage about 0 V at each terminal?

Go to Step 10.

“GRY/RED” and/or
“GRY/BLU” wire are
shorted to power circuit.
If wires are OK,
substitute a known-
good ECM and recheck.

Step

Action

Yes

No

«
...
129
130
131
132
133
...
»

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Бренд: ULTIMATE SPEED Страницы: 19

Бренд: Harbor Freight Tools Страницы: 4

Бренд: Velleman Страницы: 6

Бренд: Mazda Страницы: 720

Бренд: Pyle Страницы: 4

Бренд: MAXWORKS Страницы: 7

Бренд: Opel Страницы: 254

Бренд: Ecco Страницы: 9

2005 P207 Explorer Sport Trac

Бренд: Ford Страницы: 540

Бренд: Mercedes-Benz Страницы: 39

Бренд: Mitsubishi Страницы: 19

2013 GMC Savana

Бренд: GMC Страницы: 398

SANICON TURBO 300

Бренд: Thetford Страницы: 25

Бренд: DFI Страницы: 6

Prime Design VBI-FT31B

Бренд: Safe Fleet Страницы: 12

Бренд: Volvo Страницы: 10

Бренд: Yakima Страницы: 4

VIEWLINE TEMPERATURE GAUGES

Бренд: VDO Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды