manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Heater and Ventilation:  7A-5

HVAC Unit Removal and Installation

S4RS0A7106002

Removal

1) Disconnect negative (–) cable from battery.
2) Disable air bag system referring to “Disabling Air 

Bag System:  in Section 8B”.

3) Remove cowl top panel from vehicle body referring 

to “Cowl Top Components:  in Section 9K”.

4) Drain engine coolant, and then disconnect heater 

hoses (1) from HVAC unit (2).

5) Remove instrument panel from vehicle body 

referring to “Instrument Panel Removal and 
Installation:  in Section 9C”.

6) Remove nuts (3).
7) Remove HVAC unit from vehicle body.

Installation

Reverse removal procedure noting the following 
instructions.
• Be careful not to catch any cable and wiring harness 

in inappropriate position.

• Adjust control cables of HVAC control unit referring to 

“HVAC Control Unit Removal and Installation: ”.

• Fill engine coolant to radiator.
• Enable air bag system referring to “Enabling Air Bag 

System:  in Section 8B”.

Blower Motor Removal and Installation

S4RS0A7106003

Removal

1) Disconnect negative (–) cable from battery.
2) Disable air bag system referring to “Disabling Air 

Bag System:  in Section 8B”.

3) Disconnect connector (1) from blower motor (2).
4) Remove blower motor from HVAC unit by removing 

screws (3).

Installation

Reverse removal procedure noting the following 
instruction.
• Enable air bag system referring to “Enabling Air Bag 

System:  in Section 8B”.

Blower Motor Inspection

S4RS0A7106004

• Check for continuity between two terminals as shown. 

If there is no continuity, replace blower motor.

• Check for operation and current.

a. Put blower motor (1) in a soft-jawed vise.
b. Connect battery to blower motor as shown.
c. Check if blower motor operates smoothly without 

noise.

d. Check if ammeter indicates the specified current. 

If measured current is out of specification, replace 
blower motor.

Blower motor specified current at 12 V
16 A maximum

3

2

3

1

3

I4RS0A710004-

3

1

2

3

3

I4RS0A710005-

I4RS0A710006-

1

I4RS0A710007-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Baja Designs S8 Instructions Manual preview
S8
Бренд: Baja Designs Страницы: 6
Uniden BTSC1500 Owner'S Manual preview
BTSC1500
Бренд: Uniden Страницы: 16
Uniden BTSC1500 User Manual preview
BTSC1500
Бренд: Uniden Страницы: 20
Xblitz G250 User Manual preview
G250
Бренд: Xblitz Страницы: 16
FORM FIT HDW 1779 Installation Instructions preview
HDW 1779
Бренд: FORM FIT Страницы: 2
Hama 00201510 Operating Instructions Manual preview
00201510
Бренд: Hama Страницы: 40
Club Car Gasoline/Electric DS Golf Car 1996 Owner'S Manual preview
Gasoline/Electric DS Golf Car 1996
Бренд: Club Car Страницы: 48
Volkswagen 1973 Convertible Owner'S Manual preview
1973 Convertible
Бренд: Volkswagen Страницы: 80
Motoalliance VIPER MA11922 Install Instructions Manual preview
VIPER MA11922
Бренд: Motoalliance Страницы: 8
Hudson 1933 Eight Owner'S Manual preview
1933 Eight
Бренд: Hudson Страницы: 34
Yakima K1249 Instructions Manual preview
K1249
Бренд: Yakima Страницы: 9
Valeo Park Vision VAL632210 Instruction Manual preview
Park Vision VAL632210
Бренд: Valeo Страницы: 25
TATA Motors Indigo eCS Owner'S Manual & Service Book preview
Indigo eCS
Бренд: TATA Motors Страницы: 166
Advanced Diagnostics MVP PRO Manual preview
MVP PRO
Бренд: Advanced Diagnostics Страницы: 10
BMW FXX ATM Emulator User And Installation Manual preview
FXX ATM Emulator
Бренд: BMW Страницы: 5
SAFARI SS18HF Manual preview
SS18HF
Бренд: SAFARI Страницы: 5
Acura 2003 3.2 TL Owner'S Manual preview
2003 3.2 TL
Бренд: Acura Страницы: 347
Pogo Alert+ Operating Instructions Manual preview
Alert+
Бренд: Pogo Страницы: 40

Бренды по названию

Популярные бренды

Загрузить еще бренды