manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Automatic Transmission:  5A-55

4) Shift select lever to “N” and “D” range for 10 seconds.
5) Start vehicle and increase vehicle speed to 65 km/h (40 mile/h) with throttle position 10% or more.
6) Stop vehicle and turn ignition switch OFF.
7) Repeat Step 3) to 5) one time.
8) Stop vehicle and check DTC.

DTC Troubleshooting

DTC P0787: Shift / Timing Solenoid Control Circuit Low

S4RS0A5104042

Wiring Diagram

DTC Detecting Condition and Trouble Area

DTC Confirmation Procedure

1) Connect scan tool to DLC with ignition switch OFF, if available.
2) Clear DTC in TCM memory.
3) Start engine and shift select lever to “N” range.
4) Repeat shifting select lever from “N” range to “D” range and vice versa for 3 times.
5) Check DTC.

Step

Action

Yes

No

1

Was “A/T System Check” performed?

Go to Step 2.

Go to “A/T System 
Check: ”.

2

1) Check shift solenoid valve-A (No.1) or -B (No.2) for 

operation referring to “Solenoid Valves (Shift Solenoid 
Valves, and Timing Solenoid Valve) Inspection: ”.

Are they in good condition?

Clean fluid passage or 
replace valve body 
assembly.

Replace shift solenoid 
valve-A or -B.

1. TCM

3. A/T

2. Timing solenoid valve

[A]: Terminal arrangement of TCM connector (viewed from harness side)

DTC detecting condition

Trouble area

Voltage of timing solenoid valve TCM terminal is low although 
TCM is commanding timing solenoid valve to turn ON.

• Timing solenoid valve circuit shorted to ground
• Timing solenoid valve malfunction
• TCM

12V

C34-14

BLU/BLK

3

1

2

14

C34

C35

[A]

I4RS0A510014-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Valeo SC400 Operating Instructions Manual preview
SC400
Бренд: Valeo Страницы: 17
JAC S5 Workshop Manual preview
S5
Бренд: JAC Страницы: 70
Toyota 2012 Rav4 Owner'S Manual preview
2012 Rav4
Бренд: Toyota Страницы: 529
Yakima K343 Manual preview
K343
Бренд: Yakima Страницы: 11
APS Auto Parts Specialist iBoard IB-ZK406 Installation Instructions preview
iBoard IB-ZK406
Бренд: APS Auto Parts Specialist Страницы: 3
RAM CHASSIS CAB 3500 2017 Quick Reference Manual preview
CHASSIS CAB 3500 2017
Бренд: RAM Страницы: 16
Thule 1306 RAPID SYSTEM Fitting Instructions Manual preview
1306 RAPID SYSTEM
Бренд: Thule Страницы: 8
Mercedes-Benz R-Class Owner'S Manual preview
R-Class
Бренд: Mercedes-Benz Страницы: 373
Kia Sportage 2018 Features & Functions Manual preview
Sportage 2018
Бренд: Kia Страницы: 54
Yakima K674 Instructions Manual preview
K674
Бренд: Yakima Страницы: 13
Menabo 000081000000, Fitting Instructions Manual preview
000081000000,
Бренд: Menabo Страницы: 11
Yescom YES5062 User Manual preview
YES5062
Бренд: Yescom Страницы: 4
Z Automotive Tazer DT User Manual preview
Tazer DT
Бренд: Z Automotive Страницы: 16
Chevrolet 2014 TRAX Owner'S Manual preview
2014 TRAX
Бренд: Chevrolet Страницы: 412
Ranger design 1506-PHX Cargo Plus Installation Manual preview
1506-PHX Cargo Plus
Бренд: Ranger design Страницы: 8
AUTOTECH 10.411.01.219K Installation Instructions preview
10.411.01.219K
Бренд: AUTOTECH Страницы: 1
AutoLoc SB3PR Series User Manual And Installation Manual preview
SB3PR Series
Бренд: AutoLoc Страницы: 6
Westin 32-1660 Instructions preview
32-1660
Бренд: Westin Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды