manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Heater and Ventilation:  7A-3

Diagnostic Information and Procedures

Heater and Ventilation Symptom Diagnosis

S4RS0A7104001

Condition

Possible cause

Correction / Reference Item

Blower motor does not 
operate with blower 
speed selector ON.

Fuse blown

Check related fuses, and then check for short 
circuit to ground.

Blower motor resistor faulty

Check blower motor resistor referring to 
“Blower Motor Resistor Inspection: ”.

Blower speed selector faulty

Check blower speed selector referring to 
“Blower Speed Selector Inspection: ”.

Blower motor faulty

Check blower motor referring to “Blower Motor 
Inspection: ”.

Wiring or grounding faulty

Repair as necessary.

Incorrect temperature 
output

Temperature control cable broken or 
bent

Check temperature control cable.

Temperature control lever faulty

Check temperature control lever.

Incorrect installation of temperature 
control cable

Check position and adjust it as necessary.

Temperature control door assembly 
broken

Repair temperature control door assembly.

Air ducts clogged

Repair air ducts.

Heater core leaked or clogged

Replace heater core.

Heater hoses leaked or clogged

Replace heater hoses.

Thermostat faulty

Check thermostat referring to “Thermostat 
Inspection:  in Section 1F”.

Air outlet port does not 
change or does not agree 
with airflow selector’s 
position even if airflow 
selector is changed.

Airflow control cable broken or bent

Check airflow control cable.

Airflow control lever faulty

Check airflow control lever.

Incorrect installation of temperature 
control cable

Check position and adjust it as necessary.

Airflow control door assembly broken

Repair airflow control door assembly.

Air ducts leaked or clogged

Repair air ducts.

Air intake door does not 
change even if air intake 
mode is changed.

Air intake door broken

Repair air intake door.

Air intake control actuator faulty

Check air intake control actuator referring to 
“Air Intake Control Actuator Inspection: ”.

Air intake switch faulty

Check air intake switch referring to “Air Intake 
Switch Inspection: ”.

Wiring or grounding faulty

Repair as necessary.

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Accel 2020 Installation Instructions preview
2020
Бренд: Accel Страницы: 2
Yamaha Yamaha Rhino 660 Instruction Supplement preview
Yamaha Rhino 660
Бренд: Yamaha Страницы: 3
iArmor IA-N179 Manual preview
IA-N179
Бренд: iArmor Страницы: 6
Alpine eX-10 Installation Manual preview
eX-10
Бренд: Alpine Страницы: 8
Safe Fleet RVS-218627 Instruction Manual preview
RVS-218627
Бренд: Safe Fleet Страницы: 38
Phonocar VM338 Mounting Instructions preview
VM338
Бренд: Phonocar Страницы: 6
FAAFTECH FT-VF-HND2 Installation Manual preview
FT-VF-HND2
Бренд: FAAFTECH Страницы: 8
AutoMaxi AXIS XXL Instructions preview
AXIS XXL
Бренд: AutoMaxi Страницы: 2
Jeep GLADIATOR 2022 Owner'S Manual preview
GLADIATOR 2022
Бренд: Jeep Страницы: 380
Cadillac 2003 Seville Owner'S Manual preview
2003 Seville
Бренд: Cadillac Страницы: 402
Cobra BAK R294 Manual preview
BAK R294
Бренд: Cobra Страницы: 2
Acura 08L07-TA1-203 Installation Instructions Manual preview
08L07-TA1-203
Бренд: Acura Страницы: 6
PUTCO Molle Panels Assembly And Instruction Manual preview
Molle Panels
Бренд: PUTCO Страницы: 2
Maserati MC 20 2022 Roadside Assistance Manual preview
MC 20 2022
Бренд: Maserati Страницы: 37
Suzuki SX4 2016 Owner'S Manual preview
SX4 2016
Бренд: Suzuki Страницы: 504
Edelbrock Honda XR400 Instruction Supplement preview
Honda XR400
Бренд: Edelbrock Страницы: 2
Hudson Super Six 1916 Reference Book preview
Super Six 1916
Бренд: Hudson Страницы: 77
Fleetwood Bounder turbo diesel 2001 Instructions Manual preview
Bounder turbo diesel 2001
Бренд: Fleetwood Страницы: 166

Бренды по названию

Популярные бренды

Загрузить еще бренды