Suzuki SWIFT RS415 2017 Скачать руководство пользователя страница 600

Страница: 600 / 1257

5A-60 Automatic Transmission:

DTC Troubleshooting

Step

Action

Yes

Was “A/T System Check” performed?

Go to Step 2.

Go to “A/T System
Check: ”.

Check pressure control solenoid valve resistance

1) Turn ignition switch OFF.
2) Disconnect valve body harness connector (1), (2) on

automatic transaxle.

3) Check for proper connection to solenoid at “GRY” and

“LT GRN/BLK” circuit.

4) Check resistance of pressure control solenoid.

Pressure control solenoid valve resistance
Between terminals of transaxle side valve body
harness connector: 5.0 – 5.6

at 20

C (68

Between terminals of transaxle side valve body
harness connector and Transaxle: Infinity

Is check results satisfactory?

Go to Step 3.

Replace pressure
control solenoid valve or
valve body harness.

Check pressure control solenoid valve circuit for
ground short

1) Connect valve body harness connector.
2) Disconnect TCM connectors.
3) Check for proper connection to TCM at terminals “C34-

2” and “C34-4”. If connection is OK, check continuity
between terminal “C34-4” of disconnected harness side
TCM connector and ground.

Is continuity indicated?

“GRY” or “LT GRN/BLK”
circuit shorted to
ground.

Go to Step 4.

I3RM0B510020-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание SWIFT RS415 2017

Отзывы:

Похожие инструкции для SWIFT RS415 2017

Бренды по названию

Популярные бренды

Suzuki SWIFT RS415 2017, Руководство по обслуживанию

Результаты поиска

Содержание SWIFT RS415 2017

Отзывы:

Похожие инструкции для SWIFT RS415 2017

Бренды по названию

Популярные бренды