manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

5C-10 Clutch: 

NOTE:
When inserting transaxle input shaft to clutch 
disc, turn crankshaft little by little to match 
the splines.

 

Clutch Cover, Clutch Disc and Flywheel 
Inspection

S4RS0A5306016

Input Shaft Bearing

Check bearing (1) for smooth rotation and replace it if 
abnormality is found.

Clutch Disc

Measure depth of rivet head depression, i.e. distance 
between rivet head and facing surface.
If depression is found to have reached service limit at 
any of rivet holes (2), replace clutch disc assembly (1).

Rivet head depth
Standard: 1.65 – 2.25 mm (0.06 – 0.09 in.)
Limit: 0.5 mm (0.02 in.)

Clutch Cover

1) Check diaphragm spring (1) for abnormal wear or 

damage.

2) Inspect pressure plate (2) for wear or heat spots.
3) If abnormality is found, replace clutch cover.

Do not disassemble it into diaphragm spring and 
pressure plate.

Flywheel

Check surface contacting clutch disc for abnormal wear 
or heat spots. Replace or repair as required.

Clutch Release System Removal and 
Installation

S4RS0A5306017

Removal

1) Remove release arm by loosening its bolt.
2) Take out release bearing by turning release shaft (1).
3) Drive out No.2 bush using special tool and hammer. 

Release shaft seal will also be pushed out.

Special tool
(A):  09922-46010

4) Remove release shaft (1).

I4RS0A530018-

I3RM0A530014-

I4RS0A530019-

I3RM0A530015-

I4RS0A530020-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Trailboss HD86 Fitting Instructions preview
HD86
Бренд: Trailboss Страницы: 5
Kia Sportage 2018 Features & Functions Manual preview
Sportage 2018
Бренд: Kia Страницы: 54
KRAFTWERK Automotive 31006 Instructions preview
Automotive 31006
Бренд: KRAFTWERK Страницы: 2
Maserati Quattroporte Automatic Owner'S Manual preview
Quattroporte Automatic
Бренд: Maserati Страницы: 272
Saab 12 787 887 Installation Instructions Manual preview
12 787 887
Бренд: Saab Страницы: 12
Prorack WHISPBAR S53 Fitting Instructions For Basic Carrier preview
WHISPBAR S53
Бренд: Prorack Страницы: 10
Master Tailgaters MR-43E2DVR1 User Manual preview
MR-43E2DVR1
Бренд: Master Tailgaters Страницы: 10
Hyundai 2001 Elantra Owner'S Manual preview
2001 Elantra
Бренд: Hyundai Страницы: 168
Buick 2006 LaCrosse Getting To Know Manual preview
2006 LaCrosse
Бренд: Buick Страницы: 20
Mid America Motorworks 602-781 Instruction Sheet preview
602-781
Бренд: Mid America Motorworks Страницы: 2
Air Lift AirCELL 52205 Installation Manual preview
AirCELL 52205
Бренд: Air Lift Страницы: 12
Octocam ECO VEDR Technical Manual preview
ECO VEDR
Бренд: Octocam Страницы: 35
Cadillac ESCALADE EXT - DATASHEET 2011 Datasheet preview
ESCALADE EXT - DATASHEET 2011
Бренд: Cadillac Страницы: 1
PROUSER MCH6A Manual preview
MCH6A
Бренд: PROUSER Страницы: 40
Emerson Fisher 1052 Instruction Manual preview
Fisher 1052
Бренд: Emerson Страницы: 28
Chevrolet 2003 Venture Owner'S Manual preview
2003 Venture
Бренд: Chevrolet Страницы: 490
Champion 97053CH User Manual preview
97053CH
Бренд: Champion Страницы: 5
Champion 94842CH User Manual preview
94842CH
Бренд: Champion Страницы: 5

Бренды по названию

Популярные бренды

Загрузить еще бренды