manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

4E-15 ABS: 

EBD Warning Lamp (Brake Warning Lamp) Comes ON Steady

S4RS0A4504012

Wiring Diagram

Circuit Description

EBD warning lamp (brake warning lamp) is controlled by parking brake switch, brake fluid level switch and ABS 
hydraulic unit / control module assembly through lamp driver module in combination meter.

Troubleshooting

I4RS0A450010-

[A]: ABS hydraulic unit / control module connector E03

4. Circuit fuse box

8. Lamp driver module

1. Battery

5. Combination meter

9. ABS hydraulic unit / control module assembly

2. Main fuse box

6. ABS warning lamp 

 

3. Ignition switch

7. EBD warning lamp (Brake warning lamp)

Step

Action

Yes

No

1

1) Make sure that:

• Parking brake is completely released.
• Brake fluid level is upper than the minimum level.

Are the check results OK?

Go to Step 2.

Release parking brake 
completely and/or 
replenish brake fluid.

2

1) Turn ignition switch to ON position.

Does “ABS” warning lamp come on steady?

Perform “ABS Warning 
Lamp Comes ON 
Steady: ” previously 
outlined.

Go to Step 3.

3

1) Turn ignition switch to OFF position.
2) Disconnect ABS hydraulic unit / control module 

connector.

3) Check for proper connection to ABS hydraulic unit / 

control module connector at terminals “E03-23”.

4) If OK, apply chocks to wheels and select gear in neutral 

position.

5) Keep brake pedal depressed and start engine. Release 

parking brake.

6) Connect terminal “E03-23” of disconnected ABS 

hydraulic unit / control module connector to ground using 
service wire.

Does brake warning lamp turn off?

Substitute a known-
good ABS hydraulic unit 
/ control module 
assembly and recheck.

“PNK/BLK” circuit open. 
If wire and connection 
are OK, replace 
combination meter.

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Cadillac 2011 CTS COUPE Personalization Manual preview
2011 CTS COUPE
Бренд: Cadillac Страницы: 20
Cadillac 2011 CTS COUPE Specifications preview
2011 CTS COUPE
Бренд: Cadillac Страницы: 2
Cadillac 2009 CTS Owner'S Manual preview
2009 CTS
Бренд: Cadillac Страницы: 494
Cadillac 2008 Escalade Owner'S Manual preview
2008 Escalade
Бренд: Cadillac Страницы: 500
Cadillac 2006 Escalade Warranty And Owner Assistance Information preview
2006 Escalade
Бренд: Cadillac Страницы: 40
Cadillac 2004 DeVille Owner'S Manual preview
2004 DeVille
Бренд: Cadillac Страницы: 432
Cadillac 1997 Catera Owner'S Manual preview
1997 Catera
Бренд: Cadillac Страницы: 338
Cadillac 2009 STS Get To Know preview
2009 STS
Бренд: Cadillac Страницы: 20
Cadillac 2005 STS Owner'S Manual preview
2005 STS
Бренд: Cadillac Страницы: 438
J-Top COMPACT Instructions preview
COMPACT
Бренд: J-Top Страницы: 2
Camcar 40000 Manual preview
40000
Бренд: Camcar Страницы: 6
TATA Motors nano genX Owner'S Manual preview
nano genX
Бренд: TATA Motors Страницы: 156
Whispbar K561W Fitting Instructions Manual preview
K561W
Бренд: Whispbar Страницы: 15
Nav TV NAV-INREN Quick Manual preview
NAV-INREN
Бренд: Nav TV Страницы: 2
Nav TV PCM3CAM Install Manual preview
PCM3CAM
Бренд: Nav TV Страницы: 4
Whelen Engineering Company FastTrax FTF4 Installation Manual preview
FastTrax FTF4
Бренд: Whelen Engineering Company Страницы: 9
Honda Sedan CIVIC 2022 Manual preview
Sedan CIVIC 2022
Бренд: Honda Страницы: 701
ULTIMATE SPEED 279619 Instructions For Use And Safety Manuallines preview
279619
Бренд: ULTIMATE SPEED Страницы: 40

Бренды по названию

Популярные бренды

Загрузить еще бренды