manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

1D-45 Engine Mechanical: 

NOTE:
Before installing bearing cap, make sure that 
checking for connecting rod bolt 
deformation. Refer to “Piston Pins and 
Connecting Rods Inspection: ”.

 

Tightening torque
Connecting rod bearing cap nut (a):  15 N

˜

m 

(1.5 kg-m, 11.0 lb-ft) and then retighten by 
turning through 45

q

 twice

6) Install cylinder head referring to “Valves and Cylinder 

Head Removal and Installation: ”.

Pistons, Piston Rings, Connecting Rods and 
Cylinders Disassembly and Assembly

S4RS0A1406031

Disassembly

1) Using piston ring expander, remove two 

compression rings (Top and 2nd) and oil ring from 
piston.

2) Remove piston pin from connecting rod as follows.

a) Ease out piston pin circlips (1), as shown.

b) Force piston pin out.

Assembly

1) Decarbonize piston head and ring grooves using a 

suitable tool.

2) Install piston pin to piston (1) and connecting rod (2):

a) After applying engine oil to piston pin and piston 

pin holes in piston and connecting rod.

b) Fit connecting rod as shown in the figure.
c) Insert piston pin to piston and connecting rod.
d) Install piston pin circlips (3).

NOTE:
Circlip should be installed with its cut part 
facing as shown in the figure. Install so that 
circlip end gap comes within such range as 
indicated by arrow.

 

3) Install piston rings to piston:

• As indicated in the figure, 1st and 2nd rings have 

“T” mark respectively. When installing these piston 
rings to piston, direct marked side of each ring 
toward top of piston.

• 1st ring (1) differs from 2nd ring (2) in thickness, 

shape and color of surface contacting cylinder 
wall.
Distinguish 1st ring from 2nd ring by referring to 
the figure.

• When installing oil ring (3), install spacer first and 

then two rails.

I2RH0B140112-

I2RH0B140113-

I2RH0B140114-

I2RH0B140115-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Cadillac 2011 CTS COUPE Personalization Manual preview
2011 CTS COUPE
Бренд: Cadillac Страницы: 20
Cadillac 2011 CTS COUPE Specifications preview
2011 CTS COUPE
Бренд: Cadillac Страницы: 2
Cadillac 2009 CTS Owner'S Manual preview
2009 CTS
Бренд: Cadillac Страницы: 494
Cadillac 2008 Escalade Owner'S Manual preview
2008 Escalade
Бренд: Cadillac Страницы: 500
Cadillac 2006 Escalade Warranty And Owner Assistance Information preview
2006 Escalade
Бренд: Cadillac Страницы: 40
Cadillac 2004 DeVille Owner'S Manual preview
2004 DeVille
Бренд: Cadillac Страницы: 432
Cadillac 1997 Catera Owner'S Manual preview
1997 Catera
Бренд: Cadillac Страницы: 338
Cadillac 2009 STS Get To Know preview
2009 STS
Бренд: Cadillac Страницы: 20
Cadillac 2005 STS Owner'S Manual preview
2005 STS
Бренд: Cadillac Страницы: 438
Dakota Digital VHX-37F Installation preview
VHX-37F
Бренд: Dakota Digital Страницы: 2
Dakota Digital BIM-01-2 Manual preview
BIM-01-2
Бренд: Dakota Digital Страницы: 7
Chevrolet 2013 Spark Owner'S Manual preview
2013 Spark
Бренд: Chevrolet Страницы: 356
Ford Zephyr 2007 Owner'S Manual preview
Zephyr 2007
Бренд: Ford Страницы: 272
Pontiac 2004 Sunfire Owner'S Manual preview
2004 Sunfire
Бренд: Pontiac Страницы: 376
Jeep COMPASS 2018 Owner'S Manual preview
COMPASS 2018
Бренд: Jeep Страницы: 712
Subaru SPLASH GUARD Installation Manual preview
SPLASH GUARD
Бренд: Subaru Страницы: 3
RAM CHASSIS CAB 3500 2017 Quick Reference Manual preview
CHASSIS CAB 3500 2017
Бренд: RAM Страницы: 16
Subaru 2005 Baja Owner'S Manual preview
2005 Baja
Бренд: Subaru Страницы: 34

Бренды по названию

Популярные бренды

Загрузить еще бренды