manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

5A-52 Automatic Transmission: 

3

Check output shaft speed sensor (VSS) ground circuit

1) Turn ignition switch OFF.
2) Check continuity between “YEL/BLK” wire terminal of 

disconnected output shaft speed sensor harness side 
connector and ground.

Is continuity indicated?

Go to Step 4.

“YEL/BLK” wire open.

4

Check output shaft speed sensor (VSS) signal circuit for 
short

1) Disconnect TCM connectors.
2) Check continuity between “PPL” wire terminal of 

disconnected output shaft speed sensor harness side 
connector and ground.

Is continuity indicated?

“PPL” wire shorted to 
ground.

Go to Step 5.

5

Check output shaft speed sensor (VSS) signal circuit for 
open

1) Check continuity between “PPL” wire terminal of 

disconnected output shaft speed sensor harness side 
connector and terminal “C35-25” of disconnected 
harness side TCM connector.

Is continuity indicated?

Go to Step 6.

“PPL” wire open.

6

Inspect output shaft speed sensor (VSS)

1) Inspect output shaft speed sensor referring to “Output 

Shaft Speed Sensor (VSS) Inspection: ”.

Is check result satisfactory?

Go to Step 7.

Replace output shaft 
speed sensor (VSS).

7

Check output shaft speed sensor (VSS) gears visually

1) Check output shaft speed sensor gears for the 

followings.
• No damage in drive gear on differential case
• No damage in driven gear in output shaft speed 

sensor

Is result satisfactory?

Intermittent trouble or 
faulty TCM.
Check for intermittent 
referring to “Intermittent 
and Poor Connection 
Inspection:  in Section 
00”.
If OK, substitute a 
known-good TCM and 
recheck.

Replace drive gear and/
or driven gear of output 
shaft speed sensor.

Step

Action

Yes

No

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Kargo Master 40640 Assembly Manual preview
40640
Бренд: Kargo Master Страницы: 5
Dakota Digital VHX-37F Installation preview
VHX-37F
Бренд: Dakota Digital Страницы: 2
Dakota Digital BIM-01-2 Manual preview
BIM-01-2
Бренд: Dakota Digital Страницы: 7
K&M 8494 Installation Manual preview
8494
Бренд: K&M Страницы: 3
TrailFX A4012S Installation Instructions Manual preview
A4012S
Бренд: TrailFX Страницы: 6
Edelbrock 6883 Instructions preview
6883
Бренд: Edelbrock Страницы: 2
Toyota 1973 Crown Hardtop Owner'S Manual preview
1973 Crown Hardtop
Бренд: Toyota Страницы: 50
Axxess AX-AM-AU92 Installation Instructions Manual preview
AX-AM-AU92
Бренд: Axxess Страницы: 8
Ford 2004 Navigator Owner'S Manual preview
2004 Navigator
Бренд: Ford Страницы: 368
Rago FABRICATION R2223TTUNDM Installation Manual preview
R2223TTUNDM
Бренд: Rago FABRICATION Страницы: 10
Alpitronic Hypercharger HYC 075 Operation Instructions And Installation Manual preview
Hypercharger HYC 075
Бренд: Alpitronic Страницы: 64
SilverLeaf Electronics VMS 645 CL Owner'S Manual preview
VMS 645 CL
Бренд: SilverLeaf Electronics Страницы: 16
Acura 08L07-TA1-203 Installation Instructions Manual preview
08L07-TA1-203
Бренд: Acura Страницы: 6
Maserati Grecale 2023 Owner'S Manual preview
Grecale 2023
Бренд: Maserati Страницы: 302
Air Lift 88365 Installation Manual preview
88365
Бренд: Air Lift Страницы: 28
Dolphin DAS400 Owner'S Manual preview
DAS400
Бренд: Dolphin Страницы: 16
Saturn 2007 Ion Owner'S Manual preview
2007 Ion
Бренд: Saturn Страницы: 440
Lexus 2010 RX 350 Warranty And Services Manual preview
2010 RX 350
Бренд: Lexus Страницы: 82

Бренды по названию

Популярные бренды

Загрузить еще бренды