manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Maintenance and Lubrication:  0B-6

Exhaust System Inspection

S4RS0A0206006

WARNING:

To avoid danger of being burned, do not 
touch exhaust system when it is still hot.
Any service on exhaust system should be 
performed when it is cool.

 

When carrying out periodic maintenance, or the vehicle 
is raised for other service, check exhaust system as 
follows:
• Check rubber mountings for damage, deterioration, 

and out of position.

• Check exhaust system for leakage, loose 

connections, dents and damages.
If bolts or nuts are loose, tighten them to specification.

• Check nearby body areas for damaged, missing or 

mispositioned parts, open seams, holes, loose 
connections or other defects which could permit 
exhaust fumes to seep into the vehicle.

• Make sure that exhaust system components have 

enough clearance from the underbody to avoid 
overheating and possible damage to floor carpet.

• Any defects should be fixed at once.

Spark Plugs Replacement

S4RS0A0206007

Replace spark plugs with new ones referring to “Spark 
Plug Removal and Installation:  in Section 1H”.

Air Cleaner Filter Inspection

S4RS0A0206008

1) Remove air cleaner case clamps.
2) Take air cleaner filter out of case.
3) Check that filter is not excessively dirty, damaged or 

oily, clean filter with compressed air from air outlet 
side of filter.

4) Install air cleaner filter and then case cap by 

inserting cap tab (1) into case groove (2). Clamp cap 
securely.

Air Cleaner Filter Replacement

S4RS0A0206009

Replace air cleaner filter with new one according to 
Steps 1), 2) and 4) of “Air Cleaner Filter Inspection: ”.

Fuel Lines and Connections Inspection

S4RS0A0206010

Visually inspect fuel lines and connections for evidence 
of fuel leakage, hose cracking and damage. Make sure 
all clamps are secure.
Repair leaky joints, if any.
Replace hoses that are suspected of being cracked.

I4RS0A020003-

I2RH01140007-

I4RS0A020004-

I4RS0A020005-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

AAMP of America iSimple Operation Manual preview
iSimple
Бренд: AAMP of America Страницы: 6
MVG 0845 C Manual preview
0845 C
Бренд: MVG Страницы: 18
Toyota SUPRA 1987 Electrical Wiring Diagram preview
SUPRA 1987
Бренд: Toyota Страницы: 165
PUTCO Molle Panels Assembly And Instruction Manual preview
Molle Panels
Бренд: PUTCO Страницы: 2
Discount Car Stereo A2DIY-MBR Quick Start Bluetooth Installation Manual preview
A2DIY-MBR
Бренд: Discount Car Stereo Страницы: 8
Needit Park Mini User Manual preview
Park Mini
Бренд: Needit Страницы: 2
Gemini KIT ParkingSensor 814 Installation And Use Manual preview
KIT ParkingSensor 814
Бренд: Gemini Страницы: 6
Coolster CHALLENGER GK-6125A 2018 Manual preview
CHALLENGER GK-6125A 2018
Бренд: Coolster Страницы: 45
Porsche 928 GTS 1994 Owner'S Manual preview
928 GTS 1994
Бренд: Porsche Страницы: 127
Kargo Master 40983 Quick Start Manual preview
40983
Бренд: Kargo Master Страницы: 18
Mazda 2011 CX-9 Owner'S Manual preview
2011 CX-9
Бренд: Mazda Страницы: 605
Carbest 47804 Instruction Manual preview
47804
Бренд: Carbest Страницы: 64
Honda 08F53-T0A-100 Installation Instructions preview
08F53-T0A-100
Бренд: Honda Страницы: 2
Toyota 1998 Celica Owner'S Manual preview
1998 Celica
Бренд: Toyota Страницы: 204
FAAFTECH FT-RC-RN Installation Manual preview
FT-RC-RN
Бренд: FAAFTECH Страницы: 2
HawksHead TRACK MASTER Instruction Manual preview
TRACK MASTER
Бренд: HawksHead Страницы: 10
Axxess OESWC-7552-STK Installation Instructions Manual preview
OESWC-7552-STK
Бренд: Axxess Страницы: 8
Edelbrock 65812 Installation Instructions preview
65812
Бренд: Edelbrock Страницы: 3

Бренды по названию

Популярные бренды

Загрузить еще бренды