manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Ignition System:  1H-8

Spark Plug Removal and Installation

S4RS0A1806003

Removal

1) Remove air cleaner assembly with air intake pipe 

and cylinder head upper cover.

2) Pull out high-tension cords by gripping their caps 

and then remove ignition coil assemblies referring to 
“Ignition Coil Assembly (Including ignitor) Removal 
and Installation: ”.

3) Remove spark plugs.

Installation

1) Install spark plugs and tighten them to specified 

torque.

Tightening torque
Spark plug:  25 N·m (2.5 kg-m, 18.0 lb-ft)

2) Install ignition coil assemblies referring to “Ignition 

Coil Assembly (Including ignitor) Removal and 
Installation: ”.

3) Install high-tension cords securely by gripping their 

caps.

4) Install cylinder head upper cover and air cleaner 

assembly with air intake pipe.

Spark Plug Inspection

S4RS0A1806004

Inspect spark plug for:
• Electrode wear
• Carbon deposits
• Insulator damage
If any abnormality is found, adjust air gap, clean with 
spark plug cleaner or replace them with new plugs.

Spark plug air gap
“a”: 1.0 – 1.1 mm (0.040 – 0.043 in.)

Spark plug type
NGK: BKR6E-11
DENSO: K20PR-U11

Ignition Coil Assembly (Including ignitor) 
Removal and Installation

S4RS0A1806005

Removal

1) Disconnect negative cable at battery.
2) Remove air cleaner assembly with air intake pipe 

and cylinder head upper cover.

3) Disconnect ignition coil coupler.
4) Disconnect high-tension cord (3) from ignition coil 

assembly (2).

5) Remove ignition coil bolts (1) and then pull out 

ignition coil assembly.

Installation

1) Install ignition coil assembly (2).
2) Tighten ignition coil bolts (1) to specified torque, and 

then connect ignition coil coupler.

Tightening torque
Ignition coil bolt (a):  10 N·m (1.0 kg-m, 7.5 lb-ft)

3) Install high-tension cord (3) to ignition coil assembly 

while gripping its cap.

4) Install cylinder head upper cover and air cleaner 

assembly with air intake pipe.

5) Connect negative cable to battery.

IYSQ01181012-

I2RH0B180006-

I3RM0A180004-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Toyota 2016 RAV4 Quick Reference Manual preview
2016 RAV4
Бренд: Toyota Страницы: 56
Ultra-tow XTP Series Owner'S Manual preview
XTP Series
Бренд: Ultra-tow Страницы: 14
Mercedes-Benz 300D 2.5 1990 Owner'S Manual preview
300D 2.5 1990
Бренд: Mercedes-Benz Страницы: 121
Menabo BIKE PRO Fitting Instructions Manual preview
BIKE PRO
Бренд: Menabo Страницы: 8
Camtree G-51 Instruction Manual preview
G-51
Бренд: Camtree Страницы: 5
Honda 2010 Civic Sedan Owner'S Manual preview
2010 Civic Sedan
Бренд: Honda Страницы: 390
GMC TopKick 2007 Owner'S Manual preview
TopKick 2007
Бренд: GMC Страницы: 430
Saab 9000 1985 Service Manual preview
9000 1985
Бренд: Saab Страницы: 92
A-rival PNC70 Active Hardware Manual preview
PNC70 Active
Бренд: A-rival Страницы: 23
WABCO TP19039 Manual preview
TP19039
Бренд: WABCO Страницы: 34
RAM Cargo Van 2014 Owner'S Manual preview
Cargo Van 2014
Бренд: RAM Страницы: 666
Waeco PerfectView LCD350 Installation And Operating Manual preview
PerfectView LCD350
Бренд: Waeco Страницы: 36
Smappee EVB-1332-BL-E Installation Manual preview
EVB-1332-BL-E
Бренд: Smappee Страницы: 28
Bowers & Wilkins Turnoverball 1020 Installation Instructions Manual preview
Turnoverball 1020
Бренд: Bowers & Wilkins Страницы: 6
Oldsmobile ALERO 2001 Owner'S Manual preview
ALERO 2001
Бренд: Oldsmobile Страницы: 340
GStop GSTOP LITE Manual preview
GSTOP LITE
Бренд: GStop Страницы: 28
Toyota 2009 Tacoma Quick Reference Manual preview
2009 Tacoma
Бренд: Toyota Страницы: 22
Comelit KCA2074 Technical Manual preview
KCA2074
Бренд: Comelit Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды