manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Power Assisted Steering System:  6C-32

7) To remove the steering gear case assembly easily, 

lower the engine with transmission, but don’t 
remove.

8) Support engine with transaxle by supporting device 

and then remove engine rear mounting bolt (1).

9) Remove front suspension frame with steering gear 

case assembly referring to “Front Suspension 
Frame, Stabilizer Bar and/or Bushings Removal and 
Installation:  in Section 2B”.

10) Remove steering gear case mounting No.1 bolts (1), 

No.3 bolts (2) and gear case bracket, then remove 
gear case (3) from front suspension frame (4).

Installation

1) Mount steering gear case (1) to front suspension 

frame (2) and tighten gear case mounting No.1 bolts 
(3) and No.3 bolts (4) to specified torque.

Tightening torque
Steering gear case mounting No.1 bolt (a):  55 
N·m (5.5 kg-m, 40.0 lb-ft)
Steering gear case mounting No.3 bolt (b):  40 
N·m (4.0 kg-m, 29.0 lb-ft)

2) Install front suspension frame with steering gear 

case assembly referring to “Front Suspension 
Frame, Stabilizer Bar and/or Bushings Removal and 
Installation:  in Section 2B”.

3) Install engine rear mounting bolt (1).

Tightening torque
Engine rear mounting bracket bolt (a):  55 N·m (
5.5 kg-m, 40 lb-ft)

4) Remove supporting device.
5) Install tie-rod ends to knuckles (right & left). Tighten 

each tie-rod end nut (1) to specified torque.

Tightening torque
Tie-rod end nut (a):  45 N·m (4.5 kg-m, 32.5 lb-ft)

6) Be sure that steering wheel and brake discs (right & 

left) are all straight-ahead position and then insert 
steering lower shaft (5) into steering pinion shaft (3) 
with matching marks (4).

2

1

3

I4RS0A630040-

3

1

I4RS0A630028-

4

3

1

2

I4RS0A630029-

2

1

3,(a)

4,(b)

I4RS0A630030-

3

1,(a)

I4RS0A630031-

I3RM0A630029-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

PullRite 20K OE Series Installation Instructions Manual preview
20K OE Series
Бренд: PullRite Страницы: 10
Valeo Park Vision VAL632210 Instruction Manual preview
Park Vision VAL632210
Бренд: Valeo Страницы: 25
GYS 029422 Manual preview
029422
Бренд: GYS Страницы: 32
Roadmaster 195125 Assembly And Operating Instructions preview
195125
Бренд: Roadmaster Страницы: 4
Rugged Ridge 53701.52 Installation Manual preview
53701.52
Бренд: Rugged Ridge Страницы: 5
Cadillac 2000 DeVille Service Manual Addendum preview
2000 DeVille
Бренд: Cadillac Страницы: 19
Dodge CHALLENGER HELLCAT 2017 Owner'S Manual preview
CHALLENGER HELLCAT 2017
Бренд: Dodge Страницы: 484
Nos 05183NOS Owner'S Manual preview
05183NOS
Бренд: Nos Страницы: 22
VP Autoparts 419420 Installation preview
419420
Бренд: VP Autoparts Страницы: 2
Ford 2002 F-250 Owner'S Manual preview
2002 F-250
Бренд: Ford Страницы: 264
Yakima Safety Pole Quick Start Manual preview
Safety Pole
Бренд: Yakima Страницы: 4
Rally Armor IMF63 Installation Instruction preview
IMF63
Бренд: Rally Armor Страницы: 4
Ranger design C24-DL Installation Manual preview
C24-DL
Бренд: Ranger design Страницы: 14
DIGITAL DELAY 1014-SCR Instructions Manual preview
1014-SCR
Бренд: DIGITAL DELAY Страницы: 11
Directed 403.NISS4HT 2.36 RSR Installation Manual preview
403.NISS4HT 2.36 RSR
Бренд: Directed Страницы: 22
Davis Instruments 8126VSS Installation Manual preview
8126VSS
Бренд: Davis Instruments Страницы: 16
Jeep Cherokee 2009 Operating Information Manual preview
Cherokee 2009
Бренд: Jeep Страницы: 223
Emerson ATEX Reference Manual preview
ATEX
Бренд: Emerson Страницы: 24

Бренды по названию

Популярные бренды

Загрузить еще бренды