Suzuki SWIFT RS415 2017 Скачать руководство пользователя страница 596

Страница: 596 / 1257

5A-56 Automatic Transmission:

DTC Troubleshooting

Step

Action

Yes

Was “A/T System Check” performed?

Go to Step 2.

Go to “A/T System
Check: ”.

Check timing solenoid valve resistance

1) Turn ignition switch OFF.
2) Disconnect valve body harness connector (1), (2) on

transaxle.

3) Check for proper connection to solenoid valve at “BLU/

BLK” circuit.

4) Check resistance of solenoid valve.

Timing solenoid valve resistance
Between terminal of transaxle side valve body
harness connector and transaxle: 11 – 15

at 20

(68

Is check result satisfactory?

Go to Step 3.

Replace timing solenoid
valve or lead wire.

Check timing solenoid valve circuit for ground short

1) Connect valve body harness connector.
2) Disconnect TCM connectors.
3) Measure resistance between terminal “C34-14” of

disconnected harness side TCM connector and ground.

Is it 11 – 15

at 20

C (68

F)?

Intermittent trouble or
faulty TCM.
Check for intermittent
referring to “Intermittent
and Poor Connection
Inspection: in Section
00”.
If OK, substitute a
known-good TCM and
recheck.

“WHT/GRN” circuit
shorted to ground.

I3RM0B510018-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание SWIFT RS415 2017

Отзывы:

Похожие инструкции для SWIFT RS415 2017

Бренды по названию

Популярные бренды

Suzuki SWIFT RS415 2017, Руководство по обслуживанию

Результаты поиска

Содержание SWIFT RS415 2017

Отзывы:

Похожие инструкции для SWIFT RS415 2017

Бренды по названию

Популярные бренды