manualshive.com logo in svg

Suzuki SWIFT RS415 2017, Руководство по обслуживанию


Поделиться
Скачать
background image

Air Bag System:  8B-113

Side Curtain-Air Bag (Inflator) Module Removal 
and Installation

S4RS0A8206025

WARNING:

• Never attempt to disassemble or repair the 

side curtain-air bag (inflator) module. If any 
abnormality is found, be sure to replace it 
with new one as an assembly.

• Be sure to read “Precautions on Service 

and Diagnosis of Air Bag System: ”, 
“Precautions on Handling and Storage of 
Air Bag System Components: ” and 
“Precautions on Disposal of Air Bag and 
Seat Belt Pretensioner: ” before starting to 
work and observe every precaution during 
work. Neglecting them may result in 
personal injury or undeployment of the air 
bag when necessary.

 

Removal

1) Disable air bag system. Refer to “Disabling Air Bag 

System: ”.

2) Remove head lining referring to “Head Lining 

Removal and Installation:  in Section 9H”.

3) Disconnect side curtain-air bag (inflator) module 

connector (1) as shown in figure.
a) Unlock lock button (2).
b) With lock button unlocked, disconnect connector.

4) Remove side curtain-air bag (inflator) module fixing 

bolts (1) and clips (2).

5) Remove side curtain-air bag (inflator) module.

WARNING:

• When carrying a live air bag (inflator) 

module, make sure the bag opening is 
pointed away from you.
Never carry air bag (inflator) module by 
wires or connector on the side of the 
module. In case of an accidental 
deployment, the bag will then deploy with 
minimal chance of injury.

• As the live curtain air bag (inflator) module 

must be kept with its bag facing up while 
being stored or left standing. This is 
necessary so that a free space is provided 
to allow the air bag to expand in the 
unlikely event of accidental deployment.

• Observe “Precautions on Handling and 

Storage of Air Bag System Components: ” 
for handling and storing it.

Otherwise, personal injury may result.

 

Installation

WARNING:

Do not install side curtain-air bag (inflator) 
module while twisted or bended. Otherwise, 
side curtain-air bag (inflator) module may not 
deploy and injury may result.

 

1) Install side curtain-air bag (inflator) module (1) with 

clips and new bolts.

2) Tighten side curtain-air bag (inflator) module 

attaching bolts (1) to specified torque.

Tightening torque
Side curtain-air bag (inflator) module attaching 
bolts (a):  11 N·m (1.1 kg-m, 8.0 lb-ft)

3) Connect side curtain-air bag (inflator) module 

connector (1) securely as shown in figure.
a) Connect connector.
b) Lock connector with lock button (2).

2

1

a)

b)

I4RS0A820077-

1

2

2

2

2

1

I4RS0A820076-

1,(a)

1,(a)

I4RS0A820110-

Содержание SWIFT RS415 2017










































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SWIFT RS415 2017

Carefree Slideout Cover Service Manual preview
Slideout Cover
Бренд: Carefree Страницы: 12
Camcar 40108 Mounting Instructions preview
40108
Бренд: Camcar Страницы: 6
ABL eMH3 Quick Start Manual preview
eMH3
Бренд: ABL Страницы: 4
Ford Focus ST 2018 Supplement Manual preview
Focus ST 2018
Бренд: Ford Страницы: 38
Audi Q3 2015 - 2019 Technical Service Bulletin preview
Q3 2015 - 2019
Бренд: Audi Страницы: 12
Dometic Heki 2 Installation And Operating Manual preview
Heki 2
Бренд: Dometic Страницы: 158
Yescom YES5062 User Manual preview
YES5062
Бренд: Yescom Страницы: 4
Z Automotive Tazer DT User Manual preview
Tazer DT
Бренд: Z Automotive Страницы: 16
Jeep GLADIATOR 2022 Owner'S Manual preview
GLADIATOR 2022
Бренд: Jeep Страницы: 380
ULTIMATE SPEED 279746 Assembly And Safety Advice preview
279746
Бренд: ULTIMATE SPEED Страницы: 6
Motoalliance Denali MA11705 Manual preview
Denali MA11705
Бренд: Motoalliance Страницы: 5
Vangear Woody-Pod Instruction Manual preview
Woody-Pod
Бренд: Vangear Страницы: 5
Safe Fleet FRC SafeTrack Hardware Installation Manual preview
FRC SafeTrack
Бренд: Safe Fleet Страницы: 20
Rugged Ridge 11232.20 Quick Start Manual preview
11232.20
Бренд: Rugged Ridge Страницы: 2
Webasto H300 comfort Operating Instructions Manual preview
H300 comfort
Бренд: Webasto Страницы: 44
Sintrones SBOX-2320 User Manual preview
SBOX-2320
Бренд: Sintrones Страницы: 55
Blaupunkt 7 608 502 000 Installation Instructions Manual preview
7 608 502 000
Бренд: Blaupunkt Страницы: 6
Mitsubishi Outlander Plug-in hybrid Quick Manual preview
Outlander Plug-in hybrid
Бренд: Mitsubishi Страницы: 28

Бренды по названию

Популярные бренды

Загрузить еще бренды